background image

15 

 

When making a Warranty Claim the Buyer is obliged, on request of the Seller, to prove the purchase 
and validity of the claim by the Invoice or Bill of Delivery that incl

udes the product’s serial number, or 

eventually by the documents without the serial number. If the Buyer does not prove the validity of the 
Warranty Claim by these documents, the Seller has the right to reject the Warranty Claim. 

If  the  Buyer  gives  notice  of  a  defect  that  is  not  covered  by  the  Warranty  (e.g.  in  the  case  that  the 
Warranty Conditions were not fulfilled or in the case of reporting the defect by mistake etc.), the Seller 
is  eligible  to  require  a  compensation  for  all  the  costs  arising  from  the  repair.  The  cost  shall  be 
calculated according to the valid price list of services and transport costs. 

If the Seller finds out (by testing) that the product is not damaged, the Warranty Claim is not accepted. 
The Seller reserves the right to claim a compensation for costs arising from the false Warranty Claim. 

In case the Buyer makes a claim about the Goods that is legally covered by the Warranty provided by 
the  Seller,  the  Seller  shall  fix  the  reported  defects  by  means  of  repair  or  by  the  exchange  of  the 
damaged part or product for a new one. Based on the agreement of the Buyer, the Seller has the right 
to  exchange  the  defected  Goods  for  a  fully  compatible  Goods  of  the  same  or  better  technical 
characteristics. The Seller is entitled to choose the form of the Warranty Claim Procedures described 
in this paragraph. 

The  Seller  shall  settle  the  Warranty  Claim  within  30  days  after  the  delivery  of  the  defective  Goods, 
unless  a  longer  period  has  been  agreed  upon.  The  day  when  the  repaired  or  exchanged  Goods  is 
handed  over  to  the  Buyer  is  considered  to  be  the  day  of  the  Warranty  Claim  settlement.  When  the 
Seller is not able to settle the Warranty Claim within the agreed period due to the specific nature of the 
Goods defect, he and the Buyer shall make an agreement about an alternative solution. In case such 
agreement is not made, the Seller is obliged to provide the Buyer with a financial compensation in the 
form of a refund. 

 

CZ 
SEVEN SPORT s.r.o. 

Registered Office: 

Strakonická 1151/2c, Praha 5, 150 00, ČR 

Headquaters: 

Dělnická 957, Vítkov, 749 01 

Warranty & Service: 

Čermenská 486, Vítkov 749 01 

CRN: 

26847264 

VAT ID: 

CZ26847264 

Phone: 

+420 556 300 970 

E-mail: 

[email protected] 

  

[email protected] 

  

[email protected]  

Web: 

www.inSPORTline.cz 

SK 
inSPORTline s.r.o. 

Headquaters, warranty & service center: 

Električná 6471, Trenčín 911 01, SK 

CRN: 

36311723 

VAT ID: 

SK2020177082 

Phone: 

+421(0)326 526 701 

E-mail: 

[email protected] 

  

[email protected] 

 

[email protected] 

Web: 

www.inSPORTline.sk 

 

 

 

 

 

Summary of Contents for 22637
















Reviews: