background image

LIMITED WARRANTY 

 
 
 
 
 
 

In-Home Lifetime Warranty. 
This Warranty applies only in the United States to Inspire strength products manufactured or distributed by Health In 

Motion LLC.  The warranty period to the original purchaser is lifetime of the original purchaser.

 

Health In Motion warrants that the Product you have purchased for non-commercial, personal, family or household 
use from Health In Motion LLC or from an authorized Health In Motion reseller is free from defects in materials or 

workmanship under normal use during the warranty period.  Your sales receipt, showing the date of purchase of the 
Product, is your proof of the date of purchase.  This warranty extends only to you, the original purchaser.  It is not 

transferable to anyone who subsequently purchases the Product from you.  It excludes expendable parts such as paint 

and finish.  This Warranty becomes VALID ONLY if the Product is assembled / installed according to the instructions / 
directions included with the Product.

 

Replacement and repair of parts. 

During the warranty period Health In Motion will at no additional charge, repair or replace the Product if it becomes 
defective, malfunctions, or otherwise fails to conform with this Warranty under normal non-commercial, personal, 

family, or household use. In repairing the product Health In Motion may replace defective parts with, at the option of 

Health In Motion, serviceable used parts that are equivalent to new parts in performance, or new parts. All exchanged 
parts and Products replaced under this warranty will become the property of Health In Motion.  Health In Motion 

reserves the right to change manufacturers and or specification of any part to cover any existing warranty.

 

Service procedures. 

To obtain warranty parts, you must return the parts to Health In Motion or an authorized Health In Motion retailer in 

its original container (or equivalent).  You must pre-pay any shipping charges, taxes, or any other charges associated 

with transportation of the Product.  In addition, you are responsible for insuring any Product shipped or returned.  You 
assume the risk of loss during shipment.  You must present Health In Motion with proof-of-purchase documents 

(including the date of purchase, Model, and Serial Number).  Any evidence of alteration, erasing or forgery of proof -

of-purchase documents will be cause to void this Warranty.

 

Conditions and Exceptions. 

This Warranty does not extend to any Product not purchased from Health In Motion LLC or from an authorized Health 
In Motion reseller.  This Warranty does not extend to any Product that has been damaged or rendered defective; (a) 

as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Health In Motion; (c) by 

modification of the Product; (d) as a result of service by anyone other than Health In Motion, or an authorized Health 
In Motion warranty service provider; (e) product that has not been properly maintained (follow maintenance schedule 

found on product).  Should any product submitted for Warranty service be found to be ineligible, an estimate of repair 

cost will be furnished and the repair will be made if requested by you upon Health In Motion receipt of payment or 

acceptable arrangement of payment.

 

Disclaimer 

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY HEALTH IN MOTION MAKES NO OTHER WARRANTIES; 
EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 

PARTICULAR PURPOSE.  HEALTH IN MOTION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS 

WARRANTY.  ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS 
WARRANTY.  NEITHER HEALTH IN MOTION NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL 

OR CONSEQUENTIAL DAMAGES.  HEALTH IN MOTION IS NOT RESPOSIBLE FOR THE REPAIR OR REPLACEMENT OF 

ANY PARTS THAT HEALTH IN MOTION DETERMINES HAVE BEEN SUBJECTED AFTER THE DATE OF MANUFACTURE TO 

ALTERATION, NEGLECT, ABUSE, MISUSE, NORMAL WEAR & TEAR, ACCIDENT, DAMAGE DURING TRANSIT OR 
INSTALLATION, FIRE, FLOOD, OR ANY ACT OF GOD.  SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN 

IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO 

THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU.  This Warranty gives you specific legal rights and 
you may also have other rights that may vary from state to state.  This is the only express warranty applicable to 

Health In Motion’s “Inspire” branded strength products.  Health In Motion neither assumes nor authorizes anyone to 

assume for it any other express warranty. 

PAGE 25

 

Summary of Contents for LEG PRESS 2 OPTION




























Reviews: