InSinkErator GN3, Owner'S Manual

Page: 6 / 8

Scalding Hazard: The fa u cet d i s pen s e s near- b oilin g
(212ºF) water which can in s tantly ca us e s cal ds or
bu rn s . U s e care when operatin g thi s appliance.
Property Damage: Join remainin g t ub e
to col d water su pply only.
Property Damage: Join remainin g t ub e
to col d water su pply only.
B
■
Turn on the cold water supply.
■
Depress the dispenser’s HOT handle
and hold it until water flows from
the spout.
■
Run the water for at least 2 minutes to
flush lines (both the hot and cold handles
independently if applicable).
A
A
6
■
Check all connections to ensure they are
tight and that there are no leaks.
■
Plug in instant hot water tank.
Water will be cold at first.
Allow 12-15 minutes for water to reach
target temperature.
G urgling or hissing is normal during the
initial heating cycle.
5
■
Install a T-fitting (not included)
onto the cold water supply line.
■
Install dedicated water control valve
with 3/8" compression fitting.
■
At the end of the white 3/8" tube from the
quick-connector, slide the supplied brass
nut and ferrule over the tube and then push
in the brass tube insert.
■
Insert the white 3/8" tube into the 3/8"
compression fitting and tighten.
H C -View / H C -Wave / H C 3
■
Install a T-fitting (not included)
onto the cold water supply line.
■
Install dedicated water control valve
with 1/4" compression fitting.
■
At the end of the copper 1/4" tube,
slide the fitting’s brass nut and ferrule
over the tube.
■
Insert the copper tube into the 1/4"
compression fitting and tighten.
H-View / H-Wave / G N3 / H 99 0 / H770
A
Property Damage: A s tan d ar d g ro u n d e d o u tlet within
30" of the d i s pen s er i s req u ire d u n d er the s ink. Do
not us e an exten s ion cor d s et with the d i s pen s er.
FINAL WATER CONNECTION
FILL TANK & THEN CONNECT POWER
Brass Nut
Plastic
tube
Ferrule
Brass Insert
tube
Copper
Brass Nut
Ferrule
Di s charge
tube
From water
s upply line
To di s pen s er
Property Damage: Do not exten d the copper
line s farther than the 16" provi d e d .
Personal Injury: Do not locate filter a b ove an o u tlet or other
electrical d evice. In s tall hea d an d b racket s o that connection s
req u ire no s tretchin g , kinkin g or pinchin g of t ub in g .
It is normal for approximately 2 oz. of water to
discharge when filter is removed.
Property Damage: T ub e r u n s nee d to form to the ca b inet’ s
conto u r s to allow s tora g e s pace with no s harp b en ds . T ub e s
nee d clean, perpen d ic u lar, bu rr-free c u t s to en su re a tr u e fit.
INSTALLING FILTRATION (Optional)
A
B
■
Determine length of tubing required,
then cut to length making sure the
cut is perpendicular and burr-free.
■
Insert a white 3/8" tube into inlet
side of filter head
until it stops
.
Press in again to ensure a secure fit.
■
Insert the other white 3/8" tube
into outlet side of filter head
until it stops.
Press in again to
ensure a secure fit.
■
Mark hole locations for filter head
and bracket in a spot that allows
for filter replacement.
■
Drill 1/8" starter holes and attach
bracket to wall with wood screws,
turning until snug.
■
Remove red filter cap, insert filter
cartridge into filter head and twist
clockwise until “LOCK” arrow on the
filter aligns with arrow on bracket.
■
To redirect filter replacement water
discharge, place 6" clear tube over
vent hole on the left side of filter head.
■
Note: 3/8" fitting is required to make
connection to water supply.
■
Connect remaining white 3/8" tube
to incoming water supply line.
(See Step 5.)
C
■
Insert the copper tube(s) from the
dispenser into the 3/8" to 1/4"
quick-connect fitting.
■
Connect the white 3/8" tube
from the right outlet on the filter
head into the quick-connect fitting
until it stops.
Press in again to
ensure a secure fit.
Available as an option;
separate purchase required.
from water
supply line to dispenser
To remove tube(s) or plug from quick-connector,
depress the release ring and gently pull away.
From filter
H-View/H-Wave
G N3/H 99 0/H770
From filter
D
H C -View
H C -Wave
H C 3
Plug
10
11