Insignia NS-DWR3SS1 Installation Manual Download

Page: 4 / 24

www.insigniaproducts.com

Preparing to install your dishwasher

Parts supplied:

Tools needed:

Materials needed (kit purchased separately):

Wood screws (4)

Hose clamp

Top mounting clips (2)

Drain hose

Phillips screwdriver

Adjustable wrench

Level

Flashlight

1/4 in. and 5/16 in.
Nut driver

Tubing cutter

Flat blade
screwdriver

Safety glasses

Measuring tape

Hole saw set

Drill and bits

Gloves

New installations only

Bucket

90° Elbow, ferrule, and compression nut. (3/8
NPT external thread on one end. The other end
should be sized to fit the water supply line.

Three Wire nuts (UL listed)
(two included in kit)

Teflon thread
seal tape

Air gap (if
required)

Hand shut-off
valve

Screw-type hose clamps

Strain relief (for
electrical connections)

Electrical cable or power
cord (See

Electrical

Requirements

section)

Hot water line (min.
3/8 in. copper) kit

Waste tee for
house plumbing
(if applicable)

Coupler for extending
drain line (if applicable)

New installations only

Not included in kit

“T”connection

Garden hose
connection

Summary of Contents for NS-DWR3SS1

























Search results

Summary of Contents for NS-DWR3SS1

Reviews:

Related manuals for NS-DWR3SS1

Brands by name

Popular brands

Insignia NS-DWR3SS1, Installation Manual

Search results

Summary of Contents for NS-DWR3SS1

Reviews:

Related manuals for NS-DWR3SS1

Brands by name

Popular brands