Flip-lever
leg lock
Mounting plate
Quick-release plate
locking lever
Center column
Locking knob
Crank
handle
STORING YOUR TRIPOD
1
Remove your camera.
Note
: You can leave the quick-release plate on your camera or reattach it to
the tripod.
2
Lower the center column.
3
Open the flip-lever leg locks, then push on the legs to close the
tripod.
4
Collapse the legs, then relock the flip-lever leg locks.
5
Store the tripod in the carrying case.
IMPORTANT SAFETY INSTRUCTIONS
• Make sure that all leg locks are correctly tightened and that the legs
are fully opened before use.
• Do not carry or transport your tripod with camera equipment
attached (for example, over your shoulder or cradled in your arms).
• Do not expose your tripod to excessive heat or cold, or use near any
flame or fire.
• Do not oil or grease any part of the tripod.
• Do not use any solvents or thinners to clean your tripod. Use only a
mild detergent and wipe dry with a soft, lint-free cloth.
• Do not exceed the load limit of this tripod.
• Do not bend or put excessive pressure on the tripod legs (for
example, do not place heavy luggage on the tripod).
SPECIFICATIONS
Maximum height: 64.2 in. (163 cm)
Minimum height: 24.6 in. (62.5 cm)
Folded height: 25.2 in. (64 cm)
Weight: 3.3 lbs (1.48 kg)
Load capacity: 6.6 lbs (3 kg)
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its affiliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved.
Made in China
SETTING UP YOUR TRIPOD
1
Open the flip-lever leg locks on each leg.
Extend the leg sections from the top down
(thickest section first) to reach the height you
want.
Note
: Adjusting the thickest leg sections first gives
your tripod more stability and support.
2
Close the flip-lever leg locks to lock each leg at
the desired length.
Caution
: Securing a leg lock incorrectly can cause a leg to
retract unexpectedly and could result in damage to the
tripod or attached camera.
3
Loosen the locking collar on the center column, then
spread the legs to the preset angle. Set the tripod on a
firm surface. Tighten the locking collar to stabilize your
tripod.
4
Adjust the height of the center column by turning the locking knob
counterclockwise, turning the crank handle until the center column is
at the height you want, then tightening the knob. Turn the locking
knob clockwise to lock the center column in place.
ATTACHING YOUR CAMERA
1
Hold the quick-release plate locking lever open, then lift the mount-
ing plate to remove it.
2
Align the bottom of your camera or camcorder with the 1/4" mount-
ing screw and indexing pin (if necessary) on the plate (the rounded
side of the plate should face the camera lens), then secure your
camera or camcorder to the plate with the screw. The screw should
be tight. The indexing pin retracts if it is not required.
3
Open the quick-release plate locking lever and slide the mounting
plate onto the tripod head. Push the quick-release plate locking lever
to the left until it stops to secure the plate.
USING YOUR TRIPOD
1
Point one camera leg at your subject so you can stand between the
other two legs.
2
To adjust vertical tilt, loosen the vertical tilt lock knob, rotate the plate
up to 90 degrees, then tighten the knob.
3
To adjust horizontal tilt, turn the horizontal tilt lock handle counter-
clockwise, tilt the tripod head, then tighten the handle.
4
To pan, turn the pan locking knob counter-clockwise, pan the tripod
head, then tighten to lock in place or continue panning.
Note
: For maximum stability, always make sure that your camera lens is over
a leg.
V1 ENGLISH 16-0673
