background image

 

www.insigniarange.com

 

Last Modified: 27/01/2017

 

 20 

Silicone Seal where shown in red on the inside of the shower

 

TESTING FOR WATER LEAKS

 

LEAVE THE SHOWER 24 HOURS AFTER BUILD TO ALLOW SEALENT TO CURE AND ENSURE THE SHOWER IS 

AWAY FROM ITS FINAL POSITION TO ALLOW REAR VIEWING

 

Ensure all connections are tight and sealed including the waste, body jets and steam outlet (model dependent) on your 

shower.

 

Switch on the overhead shower NOT the massage jets, remember these will fire water out at you and are not suitable for 

checking leaks as they would normally only operate when a person is in front of them. DO NOT AIM THE HAND SHOWER 

AT THE JOINTS OF YOUR SHOWER AS THIS DOES NOT FALL UNDER 

NORMAL EVERYDAY USE

”. 

Adjust the feet 

to ensure the  direction of the water flows towards to the waste to prevent puddling.

 

Just use COLD water setting as hot will make cabin misty and condensate thus the inspection becomes very difficult. Now 

on the OUTSIDE of the shower inspect each joint, factory seal, hose, clip and jet by walking from one side and going 

around to the back and then to the other side finishing at the front. If you have a small leak (normally caused through insuf-

ficient sealer or air bubble on assembly, dry the area thoroughly and reseal.

 

Please remember the location of the water may not be exactly where the leak is as it could have run around to a low point. 

Never seal your inner fittings unless necessary, remember you will see this for the life of the shower! Again leave to cure 

and check. Once you are happy check the shower functions i.e. jets for back massage, foot massage and finally hand 

shower (model dependent) check your joints to these functions at the rear again. Never use the shower until 

all

 checks 

have been made and the installer is 100% happy in the knowledge no leaks are present. 

 

All good?

 

Now push your shower FROM THE BASE and NEVER THE GLASS OR FRAME into its final resting position.

 

                          Happy Showering! 

Silicone the area highlighted in red 

where the glass panel frame meets at 

the bottom (next to the column)

 

Silicone fill the area highlighted in red at 

the end of the bottom runner as         

indicated in the image on the left.

 

Summary of Contents for INS9012



























Reviews: