Inscape Data Link Power LPS1800-T1 User Manual Download Page 2

Page | 2 
 

Certification 

Inscape Data Corporation certifies that this product met its published specifications at time of 
shipment from the factory.  
 

FCC Statement 

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy and, if 
not installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a residential area is likely 
to cause harmful interference in which case the user will be required to correct the interference 
at his own expense. 

The user is cautioned that changes and modifications made to the equipment without approval 
of the manufacturer could void the user's authority to operate this equipment. 

The manufacturer is not responsible for any radio or TV interference caused by unauthorized 
modifications to this equipment. Such modifications could void the user’s authority to operate 
the equipment. 

 

Industry Canada Statement 

This Class A digital apparatus complies with Canadian ICES-003. 
 

CE Statement 

This product complies with the European Low Voltage Directive 73/23/EEC and EMC Directive 
89/336/EEC as amended by European Directive 93/68/EEC. 

Warning: This is a class A product. In a domestic environment this product may cause radio 
interference in which case the user may be required to take adequate measures. 

 
UL Recognized Statement 

The power supply of this product has been investigated using applicable construction and 
performance requirements by UL

, and when installed in accordance with the manufacturer’s 

installation instructions, should provide a safe, code-compliant installation.

 

 

 

Summary of Contents for Link Power LPS1800-T1















Reviews: