background image

     

SAFETY PRECAUTION

CAUTION:

The lightning flash with
arrowhead symbol, within
an equilateral triangle, is

intended to alert the user
to "dangerous voltage"
and to prevent from a risk

of electric shock.

Warning:
To reduce the risk of
electric shock, don't

open the cabinet. Refer
servicing to qualified
personnel only.

The exclamation point
within an equilateral
triangle is intended to

alert the user to important
operating and mainten-
ance(servicing).

WARNING:

Do not use this STB where contact with or immersion in water is a

possibility. Do not use near flower vase, washbowls, kitchen sinks, laundry tubs,

swimming pools, etc.

WARNING:

Do not put the candle or lamp stand on the cabinet; otherwise,

there is the danger of fire.

WARNING:

The unit should be connected to a power supply only of the type

descry bed in the operating instructions or as marked on the unit. If you are not
sure of the type of power supply(for example: 120 or 230V) to your home,

consult your local dealer or local power company.

WARNING:

Do not open the cabinet or touch any parts in the inner mechanism.

Consult your local dealer for technical service if the opening is required.

Note:

To ensure proper use of this product, please read this user manual

carefully and retain for further reference.

Note:

Do not open the cabinet to avoid the unit direct exposure to radiation.

Unit Cleaning:

After the unit power is turned off, you can clean the cabinet,

panel and remote control with a soft cloth lightly moistened with a mild
detergent solution.

Summary of Contents for X-2010




















































Reviews: