manualshive.com logo in svg

Inovonics 708, Operating And Maintenance Instruction Manual, Page: 37 / 39

Share
Download
Inovonics 708 Operating And Maintenance Instruction Manual Download Page 37

 

—      — 

35

CR10 

Diode, Zener, 22V; (open mfgr.) 1N5251 

F1 

Fuseholder, PC-mounting; Littlefuse 345-101-010 with 345-101-020 

Cap for ¼-inch (U.S.) fuses, or 345-121-020 Cap for 5mm 

(European) fuses.  (Fuse is normal “fast-blow” type in value 

specified on rear panel with reference to mains supply.) 

FB1 

Ferrite Bead; Amidon 73-801 

I1-9,16 

LED Indicator, diffused yellow, T-1 package; Stanley MAY 3378S 

I10,12,14,17, 

LED Indicator, diffused pastel red, T-1 package; Stanley MVR 3378S 

I11,13,15,18 

LED Indicator, diffused pastel green, T-1 package; Stanley MPG 3878S 

BAR1,2 

10-Segment LED-bar display module, green; Kingbright DC-10GWA 

BAR3 

10-segment LED-bar display module, yellow; Kingbright DC-10YWA 

— 

Right-angle socket for BAR1-3 (708 requires two, 14-pin and two, 16-

pin.); Circuit Assembly Corp. CA-14SE-10RAC3-01 (14-pin), 

CA-16SE-10RAC3-01 (16-pin) 

— 

Pin-strip sockets for BAR1-3; E-CAM 250-1-2510-1208 (708 requires 

three, broken into two strips of 30) 

IC1,11,23,35 

Integrated Cct.; (open mfgr.) CMOS 4051B 

IC2 

Integrated Cct.; (open mfgr.) LM317-T (Uses Aavid 574602 B03700 

Heat Fin) 

IC3 

Integrated Cct.; (open mfgr.) LM337-T (Uses Aavid 574602 B03700 

Heat Fin) 

IC4,5,27,29 

Integrated Cct.; Motorola MC34082P 

IC6,10,14,21, 

22,30-34, 

36-43,45-48 

Integrated Cct.; (open mfgr.) LF353N 

IC7,8,9 

Integrated Cct.; National Semi. LM3914N 

IC12,19,26 

Integrated Cct.; (open mfgr.) CMOS 4029B 

IC13 

Integrated Cct.; (open mfgr.) CMOS 4093B 

IC15,17 

Integrated Cct.; (open mfgr.) CMOS 4013B 

IC16 

Integrated Cct.; (open mfgr.) CMOS 4081B 

IC18 

Integrated Cct.; (open mfgr.) CMOS 4011B 

IC20 

Integrated Cct.; (open mfgr.) CMOS 4071B 

IC24,25 

Integrated Cct.; (open mfgr.) CMOS 4028B 

IC28,44 

Integrated Cct.; (open mfgr.) CMOS 4066B 

Summary of Contents for 708








































Reviews:

No comments