background image

 

 

  INOVONICS WARRANTY 

TERMS OF SALE:

  Inovonics products are sold with an understanding of 

“full satisfaction; that is, full credit or refund will be issued for products 

sold as new if returned to the point of purchase within 30 days following 

their receipt, provided that they are returned complete, and in an “as 

shipped” condition. 

II 

CONDITIONS OF WARRANTY:

  The following terms apply unless 

amended 

in writing

 by Inovonics, Inc. 

A.  Warranty Registration Card supplied with product 

must

 be completed 

and returned to Inovonics within 10 days of delivery. 

B.  Warranty applies only to products sold “as new.”  It is extended only 

to the original end-user and may not be transferred or assigned 

without prior written approval by Inovonics. 

C.  Warranty does not apply to damage caused by misuse, abuse or 

accident.  Warranty is voided by unauthorized attempts at repair or 

modification, or if the serial identification has been removed or 

altered. 

III 

TERMS OF WARRANTY:

  Inovonics, Inc. products are warranted to be 

free from defects in materials and workmanship.  
A.  Any discrepancies noted within 90 days of the date of delivery will be 

repaired free of charge, or the equipment will be replaced, at the 

option of Inovonics.  

B.  Additionally, parts for repairs required between 90 days and one year 

from the date of delivery will be supplied free of charge.  Labor for 

factory installation of such parts will be billed at the prevailing “shop 

rate.”  

IV 

RETURNING GOODS FOR FACTORY REPAIR:

  

A.  Equipment will not be accepted for Warranty or other repair without a 

Return Authorization (RA) number issued by Inovonics prior to its 

return.  An RA number may be obtained by calling the factory, and 

should be prominently displayed on the outside of the shipping 

carton.  

B.  Equipment must be shipped prepaid to Inovonics.  Shipping charges 

will be reimbursed for valid Warranty claims.  Damage sustained as 

a result of improper packing for return to the factor is not covered 

under terms of the Warranty, and may occasion additional charges.  

interstage

Phistersvej 31, 2900 Hellerup, Danmark

Telefon 3946 0000, fax 3946 0040

www.interstage.dk

-

 pro audio with a smile

Summary of Contents for 540




























Reviews: