Inovonics 540 Operating And Maintenance Instruction Manual Download Page 25

Page: 25 / 27

— —

Fuseholder, PC-mounting; Littlefuse 345-101-010 with 345-101-020

Cap for ¼-inch (U.S.) fuses, or 345-121-020 Cap for 5mm

(European) fuses. (Fuse is normal “fast-blow” type in value

specified on rear panel with reference to mains supply.)

I501-503

10-Segment LED-bar display module, green; Kingbright DC-10GWA

I504

10-Segment LED-bar display module, yellow; Kingbright DC-10YWA

I505

LED Indicator, pastel red, T-1 package; Stanley MVR 3378S

I506-508,

512,515

LED Indicator, pastel green, T-1 package; Stanley MPG 3878S

I509,513,514

LED Indicator, pastel yellow, T-1 package; Stanley MAY 3378S

I510,511

7-Segment LED alphanumeric display module; Liteon LTS 4940 AHR

or ParaLight C401E/G/W

IC1

Integrated Cct.; (open mfgr.) CMOS 4046B

IC2,3

Integrated Cct.; (open mfgr.) LM317-T (Uses Aavid 574602 B03700

Heat Fin)

IC4

Integrated Cct.; (open mfgr.) LM337-T (Uses Aavid 574602 B03700

Heat Fin)

IC5

Integrated Cct.; Motorola MC145151

IC6

Integrated Cct.;

SPECIAL FACTORY-PROGRAMMED “PIC

,”

type 16C62A. Order by designation, reference Model 540.

IC7,8,

12-14,19-27

Integrated Cct.; (open mfgr.) LF353N

IC9,15,30

Integrated Cct.; Philips NE602N

IC501-504

Integrated Cct.; (open mfgr.) LM3914N

AC Mains Connector, PC-mounting; Switchcraft EAC303

J5,6

PC-mounting TRS (stereo) ‘phone jack; Switchcraft RN 112 BPC

J601

Connector, chassis-mounting male “BNC”; Amphenol 31-221

L1-4

Inductor, 1mH; J.W. Miller 9220-2

Q1,2,3,501

Transistor, NPN; (open mfgr.) 2N3904

All

resistors

are specified as follows:

Fixed resistors

with values carried to decimal places implying a 1%

tolerance (

example:

3.01K, 10.0K, 15.0K, 332K) are ¼-watt, 1% metal

film type.

Fixed resistors

with values typical of 5% tolerance (example: 220,

3.3k, 10K, 270K) are ¼-watt, 5% carbon film type.

Multi-Turn Trimming Potentiometers

(front-panel adjustable)

are Tokos RJC097P series, Beckman 89PR series, or equivalent

“cermet” types.

Single-Turn Trimmers

(circuit board) are Tokos GF06U1 series or

Beckman 91AR series.

Switch, DPDT Slide, Voltage Selector; C&K V202-12-MS-02-QA

S501-506

Switch, SPDT Momentary Pushbutton; ITT-Schadow D6-04-01, with

F14-04 gray cap

S507

Switch, Power Rocker; Carling RA 911-RB-O-N

Summary of Contents for 540




























Search results

Summary of Contents for 540

Reviews:

Related manuals for 540

Brands by name

Popular brands

Inovonics 540, Operating And Maintenance Instruction Manual

Search results

Summary of Contents for 540

Reviews:

Related manuals for 540

Brands by name

Popular brands