Inovonics 235 Operating And Maintenance Instruction Manual Download Page 30

Page: 30 / 35

— —

Switch, DPDT Slide, Voltage Selector; C&K V202-12-MS-02-QA

Switch, SPST Toggle; C&K 7103-M-D9-A-B-E

S501-506

Switch, SPDT Momentary Pushbutton; ITT-Schadow D6-04-01, with

F14-04 gray cap

S601

Switch, Power Rocker; Carling RA 911-RB-O-N

Power Transformer, PC-mounting; Signal LP-20-600 or direct cross-

reference

MAIL-ORDER COMPONENT SUPPLIERS

The following electronic component distributors have proven

themselves reputable suppliers of small quantities of replacement parts

for professional equipment.

The temptation to use cross-referenced hobbyist or

TV-shop ‘direct replacement parts’ (ha!) should be

avoided!

Any semiconductor, IC, capacitor, resistor or connector used in the

Model 235 is

probably

available from one or more of these firms. Each

supplier publishes a full-line catalog, available free for the asking.

Minimum-order restrictions may apply; and export orders may be

difficult.

Mouser Electronics

— Call (800) 346-6873

Digi-Key Corporation

— Call (800) 344-4539

ACTIVE

(div. of Future Electronics) — Call (800) 677-8899

Allied Electronics

(div. of Avnet) — Call (800) 433-5700

Summary of Contents for 235




































Search results

Summary of Contents for 235

Reviews:

Related manuals for 235

Brands by name

Popular brands

Inovonics 235, Operating And Maintenance Instruction Manual

Search results

Summary of Contents for 235

Reviews:

Related manuals for 235

Brands by name

Popular brands