manualshive.com logo in svg

iNO DOMINATOR, Operating Instructions Manual, Page: 11 / 32

Share
Download
iNO DOMINATOR Operating Instructions Manual Download Page 11

 

 

11 

7.

 

With some tractors a number of rotations depends on the speed 
and  a  direction  of  rotating  depends  on  the  direction  of  driving. 
Take care about that. 

8.

 

Before starting the PTO shaft be sure, that noone is in the danger 
area.  

9.

 

Never try to start the PTO shaft when the tractor engine is discon-
nected.  

10.

 

It is forbidden to be in the zone of drive axle exit, when it is enga-
ged. 

11.

 

After the drive is disconnected wait that the drive axle stops to ro-
tate completely. Never approach before it stops.  

12.

 

Never carry out maintenance of a machine or tractor while the en-
gine is running. The engine should be switched off and the key re-
moved.  

13.

 

If the  PTO shaft is damaged, immediately stop with any operating. 

 

Hydraulic system 

 

1.

 

Take care! Hydraulics is under very high pressure. 

2.

 

When connecting the pipes on the tractor check that the pressure 
is not too low.  

3.

 

We recommend that an official service tests the pipes before ope-
rating and than at least ones per year. Damaged or worn outpipes 
should be replaced immediately with others of the same specifica-
tion.  

4.

 

When checking pipes it is necessary to wear protection clothes and 
gloves to avoid injuries.  

5.

 

The oil under high pressure may sweep into the skin causing seri-
ous infections. In this case contact a doctor immediately.  

6.

 

Before working  on the hydraulic system lower the machine, take 
pressure out and stop the tractor.  

7.

 

Approximate  using  period  of  the  pipes  is  6  years.  After  that  the 
pipes should be replaced to avoid any damage.  

8.

 

Used oils and greases must be stored and disposed according to 
antipollution rules. 

9.

 

 

 

Summary of Contents for DOMINATOR

































Reviews:

No comments