Innovative EBB & FLOW Assembly Instructions Manual Download Page 16

Page: 16 / 18

INNOVATIVEGROWERSEQUIPMENT.COM

Call 815-991-5010 or email us at sales@innova

vegrowersequipment.com if you have any ques

ons

EBB & FLOW BENCH TRAY GLUING INSTRUCTIONS

STEP #1

Lay trays out per included drawing. Trays should have roughly a
1/8” gap, there is a planned air gap in the end to allow for expan-
sion. Make sure all trays are si

ng level before moving on to the

next step.

STEP #2

Place glue tube (A7) in caulking gun and
cut open end (before screwing on nozzle)
to prepare to glue.

Addi

onal glue availabel for purchase at

innova

vegrowersequipment.com online store.

GLUING INSTRUCTIONS

DO NOT GLUE IN BETWEEN THE TRAYS

ONLY GLUE ON TOP OF SEAM

WHEN TRAYS MEET

SHOWN IN PICTURE

Caulk Gun

TOOLS NEEDED FOR ASSEMBLY

Razor/Knife

Summary of Contents for EBB & FLOW



















Search results

Summary of Contents for EBB & FLOW

Reviews:

Related manuals for EBB & FLOW

Brands by name

Popular brands

Innovative EBB & FLOW, Assembly Instructions Manual

Search results

Summary of Contents for EBB & FLOW

Reviews:

Related manuals for EBB & FLOW

Brands by name

Popular brands