manualshive.com logo in svg

Innovative BV20, Operation Manual

The Innovative BV20 user manual is a comprehensive configuration guide for this ground-breaking product. Discover step-by-step instructions and expert advice to optimize your experience. Download your free manual now from our website manualshive.com and unlock the full potential of your Innovative BV20.

Share
Download
background image

 

 

Copyright Innovative Technology                                                                                                                                GA794-2 

APPENDIX F - IMPLEMENTED CCTALK COMMANDS 
 

Command Header 

SIMPLE_POLL 254 

ADDRESS_POLL 253 

ADDRESS_CLASH 252 

ADDRESS_CHANGE 251 

ADDRESS_RANDOM 250 

REQUEST_POLLING_PRIORITY 249 

REQUEST_MANF_ID 246 

REQUEST_EQUIP_CAT_ID 245 

REQUEST_PRODUCT_CODE 244 

SERIAL_NUMBER 242 

REQUEST_SOFTWARE_REVISION 241 

READ_OPTO_STATES 236 

PERFORM_SELF_CHECK 232 

SET_INHIBITS 231 

REQ_INHIBITS 230 

SET_MASTER_INHIBIT 228 

REQ_MASTER_INHIBIT 227 

REQUEST_INS_COUNT 226 

REQUEST_ACCEPT_COUNT 225 

REQUEST_DATA_STORAGE_AVAIL 216 

REQUEST_OPTION_FLAGS 213 

CALCULATE_ROM_CHECKSUM 197 

REQUEST_BUILD_CODE 192 

REQUEST_BASE_YEAR 170 

REQUEST_ADDRESS_MODE 169 

READ_BUFFERED_BILL_EV 159 

REQUEST_BILL_ID 157 

REQUEST_COUNTRY_SCALING 156 

REQUEST_BILL_POSITION 155 

ROUTE_BILL 154 

MODIFY_BILL_OPERATING_MODE 153 

REQUEST_BILL_OPERATING_MODE 152 

STACKER_CYCLE 147 

OPERATE_BI_MOTORS 146 

REQUEST_CURRENCY_REVISION 145 

SWITCH_ENCRYPTION_CODE 137 

STORE_ENCRYPTION_CODE 136 

REQUEST_COMMS_REVISION 4 

RESET_DEVICE 1 

Table 16

 – Implemented ccTalk commands 

BV20 Operations Manual                                                                                          47 

Summary of Contents for BV20

















































Reviews:

No comments

Related manuals for BV20

Brands by name

Popular brands

Load more brands