Innovative BV20 Page 36 Operation Manual Download | Manualshive

Page: 36 / 48

background image

Copyright Innovative Technology Ltd 2008 GA794-2

Connecting a DA2 to a validator and PC

Figure 9

– Connecting a DA2 to a BV20 and PC for upgrading Validator Programs

Software Installation

DA1 - To install the ITL BNV Download Manager Software insert the CDROM into the

correct PC drive. The CD should automatically run and an installation menu will appear.

Double click the ITL BNV Download Manager and follow the on-screen instructions. You

can also install the Currency files, Firmware files and the Technical Manuals for each

specific product as well as other generic documentation.

The Quick Start Guide for the DA1 is document number GA151.

DA2 - To install the ITL BNV Download Manager Software insert the CDROM into the

correct PC drive. The CD should automatically run and an installation menu will appear.

Double click DA2 installation guide (GA338) and follow the instructions relating to your

specific Operating System.

NOTE: All files contained on the CD are available from the ITL website: www.innovative-

technology.co.uk

Please contact [email protected], if you require further assistance.

BV20 Operations Manual 36

«
...
34
35
36
37
38
...
»

Summary of Contents for BV20

















































Reviews:

No comments

Related manuals for BV20

Brand: Innovate Technology Pages: 39

Brand: CPI Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands