i
Px-418
e
OVER ALL DIMENSIONS & PANEL CUT OUT (IN MM)
MECHANICAL INSTALLATION
The label on the controller identifies the serial number, wiring connections and batch number.
INSTALLATION GUIDELINES :
3. Push the controller through panel cut-out and secure
1. Prepare the cut-out with proper dimension as shown in
the controller in its place by tightening the side clamp.
Figure.
2. Remove clamp from controller
CAUTION:
To prevent the risk of electrical shock, switch off the power before making/removing any connection or removing
the controller from its enclosure.
ELECTRICAL INSTALLATION :
The electrical connection diagram shown on the controller enclosure is as below.
A
B
D
E
G
F
MODEL:Px-418
e
/718
e
PANEL
CUTOUT
Glows when OP1 is ON & flashes when delay time (dly1) is in operation(if selected mode is ON-OFF)
(1) For SP programming. (2) To access Control mode. (3) To access Configuration mode along with UP key. (4) To scroll
the parameter & to store its value.
(1) To increase/alter parameter value in program mode. (2) To Enter in configuration mode (with SET key) . (3) To
acknowledge Alarm. (4) To enter in tune mode (with DOWN Key).
(1) To decrease / alter parameter value in program mode. (2) To enter in tune mode (with UP Key).
It will display (1) Measured value of selected input or Error massages in run mode.
(2) Parameters Value in program mode.
It will display (1) SP (Main set point) / SP2 (Auxiliary/Alarm) set value / Set Soak time value/ balance or elapsed soak time
in run mode. (2) Parameter code in program mode.
1
2
3
4
5
6
7
OP1 LED
UPPER
DISPLAY
LOWER
DISPLAY
SET
KEY
SHIFT
KEY
Sr.
NAME
FUNCTION
UP
KEY
DOWN
KEY
(2) Press for 3Sec in Programming this will help to go back to previous parameter.
(1) To increase/alter parameter value in program mode with Up / Dn Key.
FRONT PANEL LAYOUT DESCRIPTION :
2
Model no.
Weight (gms.)
Px-418
e
150
230
Px-718
e
OIM Px-X18
e
V2.1 Page 2 of 5
Px-718
e
TABLE : 1
Model
Dim
A
B
C
D
F
G
E
Px-418
e
Px-718
e
48
72
48
72
3
3
60
70
45
68
45
68
45
68
Px-418
e
FRONT PANEL LAYOUT
Px-718
e
5
7
1
2
3
6
4
4
5
7
1
2
3
6
NO
NC
CM
OP1-RLY
w
w
R
1
2
3
4
5
6
7
14
13
12
11
9
8
15
18
20
19
16
17
OP1-SSR
10
NO
NC
CM
OP1-SSR
OP1-RLY
1
2
3
4
5
7
8
9
10
6
R
W
W
C
This parameter will be available only if Enabled in Configuration List.
User can set ramp rate/min for SP1 (Set Point) to minimize overshoot.
RAMP
RATE
o
0.0 C
to
o
25.0 C
User can change SP value using UP/ DOWN keys. Holding the key, will
change the value at a faster rate. Press SET key to store the desired
value & move on to the next parameter.
o
0 C
Disable
LSPL ~ HSPL
CONTROL
SET
POINT
PROGRAMMING
USER LIST :
To access the user list press SET key once.
LOWER
DISPLAY
UPPER
DISPLAY
PARA
METER
RANGE
DESCRIPTION
DEFAULT
