innovair RI09C2D1 Service Manual Download Page 30

Page: 30 / 30

No/ineffective cooling
No/ineffective heating

Whether the display panel
display one of the following
signal? "Er En Eo Ed"

Er¡ -indicates room temp. sensor failure
En  indicates indoor pipe sensor failure
Eo  indicates outdoor pipe sensor failure
Ed  indicates that the evap. Is frosting

: For reverse cycle model

Whether the compressor can
start in cooling/heating mode
even if it soon stops?

Yes

Check whether the indoor
outlet/inlet of the unit
is blocked or the vent
door is open

Check temperature. setting

Check Wiring

Check compressor capacitor

Check the voltage between
RY9 on main PCB and N
on power cord

Replace the compressor

Replace the main PCB

No voltage

Check whether the indoor
outlet/inlet of the unit
is blocked or the vent
is blocked

Check whether the Evap.is

frosting and the compressor
stops frequently

Check the speed of motor

Check leakage

Recycle refrigerant and
braze the leakage point

Vaccum and recharge

Check the drainage

Check whether the Cond.is

frosting and the compressor
stops frequently

Check the speed of motor

Check the control wire of

the reverse valve

Check whether the temp. of
suction pipe is above 7

℃

Replace the capillary tube

Replace the reverse valve

Replace the compressor

Recycle refrigerant and recharge

Check the voltage between P11
on main PCB and N on power

Replace the reverse valve

Replace the Main PCB

No voltage

Yes

In cooling

Yes

Normal

Check the fan capacitor

Replace the motor

Normal

Yes

Leakage

Yes

Summary of Contents for RI09C2D1































Search results

Summary of Contents for RI09C2D1

Reviews:

Related manuals for RI09C2D1

Brands by name

Popular brands

innovair RI09C2D1, Service Manual

Search results

Summary of Contents for RI09C2D1

Reviews:

Related manuals for RI09C2D1

Brands by name

Popular brands