innovair 18K User And Installation Manual Download | Manualshive

Page: 2 / 17

background image

NOTE:

●

This heat pump air conditioner has been designed for the following temperatures.

Operate the heat pump air-conditioner within this range.

DC Inverter Unitary Series

Model

Mode

Outdoor working temperature

Maximum

Minimum

18K/24K/36K

Cooling Operation

14

℉

(-10

℃)

Heating Operation

75

℉

(24

℃

)

-13

℉

(-25

℃

)

42K

Cooling Operation

14

℉

(-10

℃)

Heating Operation

75

℉

(24

℃

)

-4

℉

(-20

℃

)

Contents

Safety instructions ..........................................................................................................................................1

Refrigerant flow diagram ................................................................................................................................3

Installation instruction....................................................................................................................................5

Installation diagram ........................................................................................................................................5

Transportation and handling before installation ............................................................................................6

Installation locations selection........................................................................................................................6

Drainage elbow and drain hose installation ...................................................................................................6

Outdoor unit installation ................................................................................................................................7

Refrigerant piping ...........................................................................................................................................7

Wiring ..........................................................................................................................................................10

Trial run .......................................................................................................................................................14

Original instructions

●

Storage condition: Temperature -13~140

℉

(

-25~60

℃

)

Humidity 30%~80%

«
1
2
3
4
...
»

Summary of Contents for 18K


















Reviews:

No comments

Related manuals for 18K

Brand: Daikin Pages: 34

Brand: DOSPEL Pages: 20

Brand: Bosch Pages: 100

PCC-1L-3210-4-7.5

Brand: Trane Pages: 24

IntelliPak WEHE Series

Brand: Trane Pages: 123

Brand: Master Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands