Innotech KIDDIELAND 062547 Manual Download Page 4

Page: 4 / 7

2206010

5. Carefully lift the old battery and replace it with a new one.

6. Put the battery retainer back in place and secure it with screws.

Plug the battery connector into the power connector, and align pins
so they are inserted together to ensure full contact is made. Secure
the seat cover back in place by securing the screw.

1. Unscrew the screw on the seat and open the seat cover.
2. Unscrew the four screws on the battery compartment

with a screwdriver and remove the battery retainer.

3. Unplug the power connector which is connected to the battery.

4. Remove the battery.

Note: Disconnect the power connector from the battery connector before conducting any maintenance procedures.
TOOLS REQUIRED: Philips Screwdriver (not included)

HOW TO REPLACE THE 6V BATTERY:

This instruction sheet must be retained as it contains important information.

GENERAL WARNING: Riding a 6-Volt Battery-Powered Police Car toy can be a dangerous activity, even under the best of circumstances. Proper

maintenance of your new Police Car toy is your responsibility and helps reduce the risk of injury. Certain conditions may cause components to fail without fault
of the manufacturer. The Police Car toy can and is intended to move, and it is therefore possible to lose control, fall off and/or get into dangerous situations that
no amount of care, instruction or expertise can eliminate. If such a thing does occur, your child can become seriously injured or die, even when using safety
equipment and other safety precautions.

WARNING: To reduce risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming

pools or other bodies of water; always wear shoes, and never allow more than one (1) rider.

SAFETY AND WARNINGS

OPTIONAL PROTECTIVE SHIELDS INCLUDED

THIS PRODUCT CONTAINS SEALED LEAD ACID BATTERIES WHICH MUST BE RECYCLED IN ACCORDANCE TO YOUR LOCAL AND STATE LAWS.

PLEASE READ CAREFULLY AND UNDERSTAND THE FOLLOWING DISPOSAL INSTRUCTIONS:

DISPOSAL:

This product contains sealed lead acid batteries which must be disposed of or recycled in an environmentally safe manner. Do not dispose of the batteries in your

household trash. Do not dispose of the batteries in a fire, as the battery may explode or leak. The incineration, disposal in landfill and/or placing sealed lead acid
batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a state or federal approved lead acid battery recycler or check with
your local retailer of vehicle batteries.

CARE

• Leaving the battery in a discharged condition will ruin it.
• Always remove an exhausted battery from the ride-on. Battery leakage and

corrosion can damage the ride-on.

• Do not store the battery on a surface which could be damaged by the acid

contained inside the battery.

• Use only the battery provided. Remember to charge the new battery for at

least 10 hours before first use.

• Examine the battery, charger and their connectors for excessive wear or

damage each time you charge the battery.

If damage is detected, do not use the charger or the battery until you have

replaced the worn or damaged part.

WARNINGS:

• Do not store the battery in temperatures above 75ºF (23.5ºC) or below 32ºF

(0ºC).

• If a battery leak develops, avoid contact with the leaking acid and place the

battery in a plastic bag. See instructions

above for proper disposal.
• If acid comes in contact with skin or eyes, flush with cool water for at least 15

minutes and call a physician immediately.

• If acid is internally ingested, give water, milk of magnesia or egg whites

immediately. Never give emetics or induce vomiting. Call a physician
immediately.

Read operator’s manual

Separate supply unit

The charger should be examined regularly for damage to the cord, plug, enclosure and other parts. In the event of such damage,
the 6-Volt Battery-Powered Police Car toy should not be charged until the charger has been repaired by qualified personnel or
replaced. Use only with charger provided with the toys.
•  Always use caution when charging.
•  The charger is not a toy and should be operated by an adult.
•  Always use the charger supplied to charge batteries for the electric Police Car.
•  Never operate the charger near flammable materials or liquids, and operate the charger in well-ventilated areas.
•  Disconnect the charger and unplug it from the 6-Volt Battery-Powered Police Car toy when not in use.
•  Do not exceed the recommended charging time.
•  Always disconnect the charger from the 6-Volt Battery-Powered Police Car toy prior to wiping down or cleaning the

electric Police Car toy with any liquid.

INSTRUCTIONS FOR USING THE CHARGER:

Your 6-Volt Battery Powered Police Car comes with 4 optional protective shields to be secured onto the front and back of the car.

page 4

CAUTION:

Use the charger in dry locations only.

1.
4 Protective shields

2.
10 screws
(including 2 extra screws)

Instructions:
1. Position 2 protective shields at

the front, and 2 protective
shields at the back as shown in
diagram.

2. Align the screw and insert 1

screw through each hole of the
protective shield to the police
car, and secure with a Philips
screwdriver. Repeat the same
until all protective shields are
secure in place.