manualshive.com logo in svg

Innoband 8520-R1, User Manual, Page: 78 / 131

Share
Download
Innoband 8520-R1 User Manual Download Page 78

 

8520-R1 4-Port Wireless N Gateway

 

78 

 

4.6.4 Service 

– IGMP Proxy 

 

Multicasting is useful when the same data needs to be sent to more than one hosts. Using multicasting 

as opposed to sending the same data to the individual hosts uses less network bandwidth. The multicast 

feature also enables you to receive multicast video stream from multicast servers. 

 

IP hosts use Internet Group Management Protocol (IGMP) to report their multicast group memberships 

to neighboring routers. Similarly, multicast routers use IGMP to discover which of their hosts belong to 

multicast groups. This device supports IGMP proxy that handles IGMP messages. When enabled, this device 

acts as a proxy for a LAN host making requests to join and leave multicast groups, or a multicast router 

sending multicast packets to multicast group on the WAN side. 

 

When a h

ost wishes to join a multicast group, it sends IGMP REPORT message to the device’s IGMP 

downstream interface. The proxy sets up a multicast route for the interface and host requesting the video 

content. It then forwards the Join to the upstream multicast router. The multicast IP traffic will then be 

forwarded to the requesting host. On a leave, the proxy removes the route and then forwards the leave to the 

upstream multicast router. 

 

The IGMP Proxy page allows you to enable multicast on WAN and LAN interfaces. The LAN interface is 

always served as downstream IGMP proxy, and you can configure one of the available WAN interfaces as the 

upstream IGMP proxy. 

 

Upstream: The interface that IGMP requests from hosts is sent to the multicast router. 

 

Downstream: The interface data from the multicast router are sent to hosts in the multicast 

group database. 

 

 

Summary of Contents for 8520-R1




































































































































Reviews:

No comments