Ingersoll-Rand W7150EU-K1, User Manual

Page: 8 / 84

EN
EN-2 48391619_ed3
Product Information: Battery Charger
Product Safety Information
WARNING
Important safety instructions - Save these instructions.
DANGER
To reduce the risk of fire or electric shock, carefully follow these instructions.
Intended Use:
This Battery Charger is designed for charging Ingersoll Rand batteries only.
WARNING
Only use Ingersoll Rand charger with Ingersoll Rand IQ
V20
Series Li-Ion batteries. Use of other batteries or chargers may create a risk of fire or
may cause battery to burst when charging. Personal injury or property damage may result.
Charger is not user serviceable. Repair should only be carried out by an Ingersoll Rand Authorized Service Center. User service may result
in electric shock, fire and/or serious personal injury.
This is a class A product. In a residential, commercial or light industrial environment it may cause radio interference. This product is not
intended to be installed in a residential environment; in a commercial and light industrial environment with connection to the public mains sup-
ply, the user may be required to take measures to reduce interference.
This product is not intended to be used by travelers.
For additional information, refer to Battaery Charger Safety Information Manual Form 10567832 and Battery Safety Information Manual
Form 10567840.
Manuals can be downloaded from www.ingersollrandproducts.com.
Product Specifications
Model Input Output
Battery
Type Voltage Model Number Rated Capacity
BC1120
100-240V AC ~ 50/60Hz,
100W, 160-215VA
21V DC, 4.0A Li-Ion
20V BL2010 3.0 Ah
20V BL2005 1.5 Ah
USB Type A
5V DC, 500mA
USB Dedicated Charging Port
D+ / D- Connected, 200 Ω
Instructions for Charging Battery
The charger shall be installed near a socket-outlet that is easily accessible.
Do not charge battery pack when temperature is below 32°F (0°C) or above 113°F (45°C). Completely charge new battery packs before using.
Charging time is approximately 60 minutes. Unplug charger and remove battery pack when not in use.
Action Condition
Charger Display Alarm
(Sound)
Fuel
Gauge Green Red
Plug charger into 100-
240V AC power outlet. Power On (Stand-By).
l m
-
mmmm
Insert battery pack into
charger.
Charging.
Fuel gage will indicate state of charge.
l m
-
ä
mmm
Ê
Communications Failure.
Battery Identification / Read Fault. Reinsert battery. Battery may be defective.
m l Low
♪
mmmm
Initial Temperature.
Charging paused until battery has returned to safe temperature.
m
2 x
ä
Low
♪
mmmm
Time Out.
Charge time exceeded. Battery may be defective.
m
3 x
ä
Low ♪
mmmm
In Cycle Temperature.
Charging paused until battery has returned to safe temperature.
m
4 x
ä
Low ♪
mmmm
Over Voltage.
High voltage detected. Battery may be defective.
m
5 x
ä
Low ♪
mmmm
Over Current.
High current detected. Battery may be defective.
m 6 x
ä
Low ♪
mmmm
Remove battery pack. Charge Completed. l m High
♪ ♪ ♪
llll
Legend:
ä
Flash
l
On
m
Off
Routine Maintenance
Unplug charger before cleaning. Plastic surfaces should only be cleaned with a slightly damp cloth. Keep vents free of dust and debris.
Charger should not be used with a damaged cord. Replacement cords and labels are available at nearest authorized Ingersoll Rand Service Center.
Refer all communications to nearest Ingersoll Rand Office or Distributor.
Environmental Protection
When life of Ingersoll Rand electrical product has expired, it must be recycled in accordance with all applicable standards and regulations (local,
state, country, federal, etc.). Improper disposal may endanger environment.
Symbol Identification
Li-Ion
Return waste material
for recycling.
Do not dispose of this product with
household waste material.
Product contains Lithium-Ion.
Do not dispose of this product with household waste material.
Original instructions are in English. Other languages are a translation of the original instructions.
•
•
•
•