Disconnect the power at the breaker. Remove the grill by grasping it in the middle, flex grill up and lift it off.
Unscrew and remove both end reflectors. Unhook element clips at each end of the heater and remove nuts from
end of element to remove the existing quartz tube. Carefully install the new element. Remove one nut from end
of the new element. Install wire by sliding high temperature ring terminal onto element screw and replace nut.
Use a thin 11/32" wrench to hold inside nut. Nuts must make a tight connection. Reinstall end reflectors, then
snap protective grill back in place.
REPLACEMENT ELEMENT INSTALLATION
NOTE: Hold ceramic element firmly while tightening nut
to prevent damage to element. Nut should be
tightened snug. A loose connection can cause the
element to short or fail prematurely. Connect the
side of element in like manner. Close element
clips over tube. Replace end reflectors.
11/32” OUTSIDE NUT
11/32” INSIDE NUT
(SNUG TO CERAMIC)
(Visit infratech-usa.com for video instructions)
PART# ELEMENT# LENGTH WATTS VOLTS FITS MODELS
10-1020
E-7512 16 - ½” (0.4m) 750
120 W-7512
10-1050
E-1412 30" (0.8m) 1500
120 W-1512
10-1055
E-1424
30” (0.8m)
1500
240 W-1524/WD-3024
10-1085
E-2024 36" (0.9m) 2000
240 W-2024/WD-4024
10-2010 E-2524 36" (0.9m) 2500
240 W-2524/WD-5024
10-2030 E-3024 58" (1.5m) 3000
240 W-3024/WD-6024
10-2055 E-4024 58" (1.5m) 4000
240 W-4024
REPLACEMENT ELEMENTS - (OTHER VOLTAGES ALSO AVAILABLE)
Need help?
To order
replacement elements for your
Infratech heating system,
please contact us via phone or
visit our website.
Consult the label located on the
back of heater for proper watts,
voltage, and replacement
element part number
.
13-1210
Single Element End Reflector (Set of 2)
1
13-1252
Dual Element End Reflector (Set of 2)
1
13-1202, 13-1200, 13-1205 Body Reflector – Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
1
13-1242, 13-1240, 13-1245
Grill Guard
- Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
Lead Wire Set - Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
13-1232, 13-1230, 13-1235 Note: Dual Element Heaters require 2 Lead Wire Sets per Heater
1
22-1151
S.S. Mounting Bracket (Set of 2)
1
18-2295,18-2300, 18-2305 Flush Mount S.S. Frame – Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
1
REPLACEMENT PARTS
PART#
PART DESCRIPTION
QUANTITY
5
Disconnect the power at the breaker. Remove the grill by grasping it in the middle, flex grill up and lift it off.
Unscrew and remove both end reflectors. Unhook element clips at each end of the heater and remove nuts from
end of element to remove the existing quartz tube. Carefully install the new element. Remove one nut from end
of the new element. Install wire by sliding high temperature ring terminal onto element screw and replace nut.
Use a thin 11/32" wrench to hold inside nut. Nuts must make a tight connection. Close element clips over tube,
reinstall end reflectors, then snap protective grill back in place.
NOTE: Hold ceramic element firmly while tightening nut
to prevent damage to element. Nut should be
tightened snug. A loose connection can cause the
element to short or fail prematurely.
Disconnect the power at the breaker. Remove the grill by grasping it in the middle, flex grill up and lift it off.
Unscrew and remove both end reflectors. Unhook element clips at each end of the heater and remove nuts from
end of element to remove the existing quartz tube. Carefully install the new element. Remove one nut from end
of the new element. Install wire by sliding high temperature ring terminal onto element screw and replace nut.
Use a thin 11/32" wrench to hold inside nut. Nuts must make a tight connection. Reinstall end reflectors, then
snap protective grill back in place.
REPLACEMENT ELEMENT INSTALLATION
NOTE: Hold ceramic element firmly while tightening nut
to prevent damage to element. Nut should be
tightened snug. A loose connection can cause the
element to short or fail prematurely. Connect the
side of element in like manner. Close element
clips over tube. Replace end reflectors.
11/32” OUTSIDE NUT
11/32” INSIDE NUT
(SNUG TO CERAMIC)
(Visit infratech-usa.com for video instructions)
PART# ELEMENT# LENGTH WATTS VOLTS FITS MODELS
10-1020
E-7512 16 - ½” (0.4m) 750
120 W-7512
10-1050
E-1412 30" (0.8m) 1500
120 W-1512
10-1055
E-1424
30” (0.8m)
1500
240 W-1524/WD-3024
10-1085
E-2024 36" (0.9m) 2000
240 W-2024/WD-4024
10-2010 E-2524 36" (0.9m) 2500
240 W-2524/WD-5024
10-2030 E-3024 58" (1.5m) 3000
240 W-3024/WD-6024
10-2055 E-4024 58" (1.5m) 4000
240 W-4024
REPLACEMENT ELEMENTS - (OTHER VOLTAGES ALSO AVAILABLE)
Need help?
To order
replacement elements for your
Infratech heating system,
please contact us via phone or
visit our website.
Consult the label located on the
back of heater for proper watts,
voltage, and replacement
element part number
.
13-1210
Single Element End Reflector (Set of 2)
1
13-1252
Dual Element End Reflector (Set of 2)
1
13-1202, 13-1200, 13-1205 Body Reflector – Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
1
13-1242, 13-1240, 13-1245
Grill Guard
- Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
Lead Wire Set - Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
13-1232, 13-1230, 13-1235 Note: Dual Element Heaters require 2 Lead Wire Sets per Heater
1
22-1151
S.S. Mounting Bracket (Set of 2)
1
18-2295,18-2300, 18-2305 Flush Mount S.S. Frame – Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
1
REPLACEMENT PARTS
PART#
PART DESCRIPTION
QUANTITY
5
Disconnect the power at the breaker. Remove the grill by grasping it in the middle, flex grill up and lift it off.
Unscrew and remove both end reflectors. Unhook element clips at each end of the heater and remove nuts from
end of element to remove the existing quartz tube. Carefully install the new element. Remove one nut from end
of the new element. Install wire by sliding high temperature ring terminal onto element screw and replace nut.
Use a thin 11/32" wrench to hold inside nut. Nuts must make a tight connection. Reinstall end reflectors, then
snap protective grill back in place.
REPLACEMENT ELEMENT INSTALLATION
NOTE: Hold ceramic element firmly while tightening nut
to prevent damage to element. Nut should be
tightened snug. A loose connection can cause the
element to short or fail prematurely. Connect the
side of element in like manner. Close element
clips over tube. Replace end reflectors.
11/32” OUTSIDE NUT
11/32” INSIDE NUT
(SNUG TO CERAMIC)
(Visit infratech-usa.com for video instructions)
PART# ELEMENT# LENGTH WATTS VOLTS FITS MODELS
10-1020
E-7512 16 - ½” (0.4m) 750
120 W-7512
10-1050
E-1412 30" (0.8m) 1500
120 W-1512
10-1055
E-1424
30” (0.8m)
1500
240 W-1524/WD-3024
10-1085
E-2024 36" (0.9m) 2000
240 W-2024/WD-4024
10-2010 E-2524 36" (0.9m) 2500
240 W-2524/WD-5024
10-2030 E-3024 58" (1.5m) 3000
240 W-3024/WD-6024
10-2055 E-4024 58" (1.5m) 4000
240 W-4024
REPLACEMENT ELEMENTS - (OTHER VOLTAGES ALSO AVAILABLE)
Need help?
To order
replacement elements for your
Infratech heating system,
please contact us via phone or
visit our website.
Consult the label located on the
back of heater for proper watts,
voltage, and replacement
element part number
.
13-1210
Single Element End Reflector (Set of 2)
1
13-1252
Dual Element End Reflector (Set of 2)
1
13-1202, 13-1200, 13-1205 Body Reflector – Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
1
13-1242, 13-1240, 13-1245
Grill Guard
- Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
Lead Wire Set - Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
13-1232, 13-1230, 13-1235 Note: Dual Element Heaters require 2 Lead Wire Sets per Heater
1
22-1151
S.S. Mounting Bracket (Set of 2)
1
18-2295,18-2300, 18-2305 Flush Mount S.S. Frame – Fits 33”(0.8m), 39” (1.0m), 61- ¼” (1.6m)
1
REPLACEMENT PARTS
PART#
PART DESCRIPTION
QUANTITY
5
PART#
ELEMENT# LENGTH
WATTS
VOLTS
FITS MODELS
10-1020 E-7512
16½” (0.4m) 750
120
W-7512
10-1050 E-1412 30” (0.8m) 1500 120 W-1512
10-1055 E-1424 30” (0.8m) 1500 240 W-1524/WD-3024
10-1085 E-2024 36” (0.9m) 2000 240 W-2024/WD-4024
10-2010 E-2524 36” (0.9m) 2500 240 W-2524/WD-5024
10-2030 E-3024 58” (1.5m) 3000 240 W-3024/WD-6024
10-2055 E-4024 58” (1.5m) 4000 240 W-4024
11/32” OUTSIDE NUT
11/32” INSIDE NUT
(SNUG TO CERAMIC)
