background image

 

 

11

SunLight Series UPS User Manual 

 
 
 
 
 
 

IV.  OPERATING   PROCEDURE 

 
 

4.1     6 - 7,5 - 10 kVA

 

 

4.1.1  Turn On procedure 

 

1 .

 Turn on  the Main Switch  on the rear panel to "

1

"  position. 

(There is line voltage at the output.)

  

2 .

  Turn on  the On-Off Switch PK1  on  the rear panel to  the "

1

"  position. Turn on the power switches on  

your critical load after the "Inverter" indicator (green light) is turned on. 

(There is inverter voltage at the 

output.)

 

 
 

4.1.2   Turn Off procedure 

 
1 .

  Turn off all the power switches on your critical equipments that are connected to the UPS. 

2 .

 Turn off the On-Off switch PK1 and the Main Switch to "

0

" position. 

 

CAUTION

 

A-

  For  daily   TURN   ON / TURN   OFF   operation,  it  is  recommended  to keep  the Main switch  at "

1

"      

     position  to  ensure  proper  battery  operation. 

B-

  If  the  Main  switch   is  in   "

1

"  position   the  line  power will be supplied   to output receptacles  

     directly. DO NOT insert objects other than equipment  power cords into outlets. 
 

 
 

4.2     15-20-30  kVA

 

 

4.2.1  Turn On Procedure 

 
1 .

  Turn On Main Switch PK1 on the front  panel from position "

0

" to "

3

" step by step as in the instructions  

      given in chapter 3.4.2 

2 .

  Turn on the power switches on your critical load after the "Inverter" indicator (green light) is turned on.   

      You will have an uninterrupted AC supply voltage at the UPS outputs only if this green light is "

ON

"     

      and  if you have a by-pass supply connected to your unit. 
 
 

4.2.2  Turn Off Procedure 

 
1 .

 Turn off all the power switches on your critical equipments that are connected to the UPS . 

2 .

 Turn off the Main switch PK1 "

0

" position step by step. 

 

CAUTION

 

A .

  Regardless of the position of PK1 , the battery charger is active as long as the battery fuse and AC  

       circuit breakers are closed. 

B .

  For  daily   TURN   ON / TURN   OFF    operation ,   it  is recommended to keep the Main switch PK1  

       in "

0

" position. 

 
 

4.3  When Utility Power Is Interrupted 

 
In case the utility power is interrupted, the UPS converts the built-in battery source to output terminals 
immediately to protect your critical loads from loss of data or damage. 

Summary of Contents for SunLight -210























Reviews: