background image

 

 

2

SunLight Series UPS User Manual 

I. SAFETY 

 
This manual contains important instructions for SUNLIGHT series UPS that should be followed during 
installation and maintenance. 

 

IMPORTANT  NOTICES 

 

1. 

Read instructions carefully before operating the UPS 

 

2. 

All warnings in the manual should be adhered to. 

 

3. 

All operating instructions should be followed. 

 

4. 

The unit should be supplied by a grounded outlet. Do not operate the unit  without ground source. 

 

5. 

Power cord of the UPS should be routed carefully so that they are not to be walked on. 

 

6. 

Please save this manual. 

 

7. 

Please save or recycle the packaging materials. 

 

WARNING! 

 

 

Do not insert any object into ventilation holes or other openings. 

 

To reduce the risk of fire or electric shock, install in temperature and humidity controlled indoor 
area free of conductive contaminants.  

 

To reduce the risk of fire, replace fuses with the same type and rating when necessary. 

 

CAUTION! 

 

 

Only qualified  personnel should install or service UPS/batteries.

 

 

 

Risk of electric shock, do not remove cover. No user serviceable parts  inside, refer    
servicing to qualified service personnel.

  

 

 

The output may be energized when the unit is not connected to a mains supply. 

 

 

Risk of electric shock  hazardous live parts inside this unit are  energized from the battery 
supply even when the input AC power is connected.

 

 

 

To reduce the risk of electric shock, disconnect the UPS from the mains supply before installing a 
computer interface signal cable. Reconnect the power cord only after signalling interconnections 
have been made. 

 

ABOUT THE BATTERY  

 

 

A battery can present a risk of electric shock  or burn from high short circuit currents. The 
following precaution should be observed when working on batteries : 

 

 

 

 

* Remove watches, rings or other metal objects. 

 

 

* Use tools with insulated handles. 

 

The batteries in this UPS are recyclable. Batteries must be disposed of according to local 
environmental laws. The batteries contain lead and pose a hazard to the environment and human 
health if not disposed of properly.  

 

 

Do not dispose of batteries in a fire. The batteries will explode. Do not open or mutilate the 
batteries. They contain an electrolyte which is toxic and harmful to the skin and eyes. If 
electrolyte comes into contact with the skin the affected area should be washed immediately. 

 

 

The internal energy source (the battery) cannot be de-energized by the user.  

 

Summary of Contents for SunLight -210























Reviews: