manualshive.com logo in svg

Infinova V6202-T03 Series, Instruction Manual

Share
Download
Infinova V6202-T03 Series Instruction Manual Download Page 41

37 

352

×

288, 352

×

240 and closed. 

For MJPEG stream, the resolution comes to 2048

×

1536, 1920

×

1080, 

1280

×

1024, 1280

×

720, 720

×

480 and closed. 

 

 

Frame Rate:

 the number of compressed frames produced by camera per 

second. 
The bigger the frame is, the better the image continuity will be, but the CPU 
performance is lowered. 
The smaller the frame is, the worse the image continuity will be, but the CPU 
could handle more events. 
For H.264 major stream, the maximum frame rate is 20fps when the resolution 
comes to 2048

×

1536; the maximum frame rate is 30fps when the resolution 

comes to 1920

×

1080. 

The maximum frame rate for MJPEG is 10fps. 
Note: the video settings of H.264 major/minor stream are linkage with that of 
MJPEG stream. When the three streams are enabled, the resolution/frame rate 
settings are as below:   
a.

 

H.264 major stream: the resolution is 

2048

×

1536,

 and frame rate is 

20fps; 

b.

 

H.264 minor stream: the resolution is 

720

×

480,

 and frame rate is 

20fps; 

c.

 

MJPEG 

stream: the resolution is 

720

×

480,

 and frame rate is 

9fps.

 

If it prompts the setting failed, please 

operate according to the prompt.

 

 

GOV number:

 GOV number means the ratio of I frame to P frame in compressed 

video images. 

The bigger the value is, the less the data quantity is and the less network 

resource it occupies.   

Max. 

GOV number

 can be set to 60. 

 

Bit Rate:

 There are 2 modes of bit rate: variable rate (vbr) and constant rate 

(cbr). 

Summary of Contents for V6202-T03 Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands