16
front-end device.
For example, the address of the dome camera is 3, baud rate is 2400
and protocol is Infinova protocol, the setting of DVR must be the
same.
Press "Save" after finishing settings, the settings will take effect
immediately, it's unnecessary to reboot the DVR. Select "Exit" to
quit from the PTZ setting interface.
4.4.2 PTZ Control
There're 3 ways to perform PTZ control.
(1) PTZ control from menu. Select "PTZ control" option after
enter the PTZ/COM menu, as shown in Figure 4-5.
Figure 4-5
(2) PTZ control via front panel. The operation is shown as
follows:
In the preview status, press
Ǐ
PTZ
ǐ
key to enter PTZ control status.
There will be a login window if the operation password is enabled.
Login with the user name that has the authority to perform PTZ
control and correct password, and then control the direction
movement by
Ǐ
ǐ
,
Ǐ
ǐ
,
Ǐ
ǐ
and
Ǐ
ǐ
keys.
Quick press
Ǐ
ǐ
and
Ǐ
ǐ
key to decrease and increase the speed
respectively, total 8 levels of speed, adjust circularly.
Press
Ǐ
ESC
ǐ
or
Ǐ
ENT
ǐ
key to exit after operation.
(3) In the 1 screen preview interface, click the arrow that popped
out to control the movement direction of the dome.
4.4.3 Set and Call Preset
1. Set preset
The preset number should be within 1-255. In Figure 4-5, move the
cursor to the "Preset" by
Ǐ
ǐ
,
Ǐ
ǐ
,
Ǐ
ǐ
and
Ǐ
ǐ
keys, and
press
Ǐ
ENT
ǐ
key to enter editing status. Input the preset number,
then press
Ǐ
ENT
ǐ
key to save the setting, and then move the
cursor to "Set" and press
Ǐ
ENT
ǐ
key to confirm the setting.
2. Call Preset
There're 2 methods to call preset, as follows:
Method 1: As shown in Figure 4-5, input the preset number, for
example 1, and then press "Call" to call up the preset 1.
Method 2: In the PTZ control status, press
Ǐ
PRST
ǐ
key, and then
input 3 number combination keys to call up the preset. For example,
if want to call up preset 002, after press
Ǐ
PRST
ǐ
key, input
Ǐ
0
ǐ
Ǐ
0
ǐǏ
2
ǐ
, then the preset 002 is called up.
4.4.4 Set and Call Pattern
1. Set pattern
The DVR supports maximum 4 patterns only. In the interface as
shown in Figure 4-5, move the cursor to "Pattern", and press
Ǐ
ENT
ǐ
key to enter editing status, and then input desired number,
at last press
Ǐ
ENT
ǐ
key to save the setting. Move the cursor to
"Start" button, and press
Ǐ
ENT
ǐ
key, now on the screen there will
be a message to indicate the pattern is ready to set, such as SET
PATTERN XXX". Move the cursor to the direction keys, and press
Ǐ
ENT
ǐ
key to confirm the movement direction. After finishing
setting, move the cursor to "Stop" button, and press
Ǐ
ENT
ǐ
key to
stop and save the pattern setting.
2. Call pattern
In the interface as shown in Figure 4-5, input the pattern number,
for example 1, press "Call", and then the pattern 1 is called.
Note
: The pattern could be called up by calling presets, and the
method varies from different domes or pan/tilt, please refer to the
manual of dome and pan/tilt for details. For example, for the domes
or pan/tilt cameras with Infinova protocol, the pattern 1 to 4 could
be called by calling up preset 70 to 73.
4.5 Alarm
The DVR supports three different types of alarm, channel, input and
exception alarm.
4.5.1 Channel Alarm
The channel alarm includes video mask alarm, video loss alarm and
motion detection alarm.
It will generate alarm if there's video mask in that channel;
It will generate alarm if there's video loss in the that channel;
It will generate video motion detection alarm and linkage if there's
motion detection.
Enter the channel setting from the "Channel" in the main menu,
press
Ǐ
WIDE
ǐ
key to switch to "Advanced Settings" option, as
shown in Figure 4-6.
