Infineon Cypress EZ-BLE CYBLE-012011-00 Manual Download Page 30

Page: 30 / 40

Document Number: 002-02521 Rev. *G

Page 29 of 39

CYBLE-012011-00

Environmental Specifications

Environmental Compliance

This Cypress BLE module is built in compliance with the Restriction of Hazardous Substances (RoHS) and Halogen Free (HF)

directives. The Cypress module and components used to produce this module are RoHS and HF compliant.

RF Certification

The CYBLE-012011-00 module will be certified under the following RF certification standards at production release.

■

FCC: WAP2011

■

IC: 7922A-2011

■

MIC: 203-JN0509

■

KC: MSIP-CRM-Cyp-2011

Safety Certification

The CYBLE-012011-00 module complies with the following regulations:

■

Underwriters Laboratories, Inc. (UL) - Filing E331901

■

CSA

■

TUV

Environmental Conditions

Table 51

describes the operating and storage conditions for the Cypress BLE module.

Table 51. Environmental Conditions for CYBLE-012011-00

ESD and EMI Protection

Exposed components require special attention to ESD and electromagnetic interference (EMI).
A grounded conductive layer inside the device enclosure is suggested for EMI and ESD performance. Any openings in the enclosure

near the module should be surrounded by a grounded conductive layer to provide ESD protection and a low-impedance path to ground.

Device Handling

: Proper ESD protocol must be followed in manufacturing to ensure component reliability.

Description

Minimum Specification

Maximum Specification

Operating temperature

-40 °C

85 °C

Operating humidity (relative, non-condensation)

85%

Thermal ramp rate

–

3 °C/minute

Storage temperature

–40 °C

85 °C

Storage temperature and humidity

–

85 ° C at 85%

ESD: Module integrated into system

Components

[10]

–

15 kV Air

2.2 kV Contact

Note

10. This does not apply to the RF pins (ANT, XTALI, and XTALO). RF pins (ANT, XTALI, and XTALO) are tested for 500-V HBM.

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Summary of Contents for Cypress EZ-BLE CYBLE-012011-00









































Search results

Summary of Contents for Cypress EZ-BLE CYBLE-012011-00

Reviews:

Related manuals for Cypress EZ-BLE CYBLE-012011-00

Brands by name

Popular brands

Infineon Cypress EZ-BLE CYBLE-012011-00, Manual

Search results

Summary of Contents for Cypress EZ-BLE CYBLE-012011-00

Reviews:

Related manuals for Cypress EZ-BLE CYBLE-012011-00

Brands by name

Popular brands