manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

System Units (Vol. 1 of 2)

System Timer

 

User’s Manual

15-1

V2.0, 2007-07

STM, V2.0

 

15

System Timer

15.1

Overview

This chapter describes the System Timer (STM). The TC1796’s STM is designed for
global system timing applications requiring both high precision about long periods. The
STM has the following features:
•

Free-running 56-bit counter

•

All 56 bits can be read synchronously

•

Different 32-bit portions of the 56-bit counter can be read synchronously

•

Flexible interrupt generation based on compare match with partial STM content

•

Driven by max. 75 MHz clock (=

f

SYS

, default after reset = 

f

SYS

/2)

•

Counting starts automatically after a reset operation

•

STM is reset by:
– Watchdog reset
– Software reset (RST_REQ.RRSTM must be set)
– Power-on reset

•

STM (and clock divider STM_CLC.RMC) is not reset at a hardware reset 
(HDRST = 0)

•

STM can be halted in debug/suspend mode (via STM_CLC register)

Special STM register semantics provide synchronous views of the entire 56-bit counter,
or 32-bit subsets at different levels of resolution.
The maximum clock period is 2

56

×

f

STM

. At 

f

STM

= 75 MHz, for example, the STM counts

30.47 years before overflowing. Thus, it is capable of continuously timing the entire
expected product life-time of a system without overflowing.

15.2

Operation

The STM is an upward counter, running either at the system clock frequency 

f

SYS

 or at a

fraction of it. The STM clock frequency is 

f

STM

=

f

SYS

/RMC with RMC = 0-7 (default after

reset is 

f

STM

=

f

SYS

/2, selected by RMC = 010

B

). RMC is a bit field in register STM_CLC.

In case of a power-on reset, a watchdog reset, or a software reset, the STM is reset. After
one of these reset conditions, the STM is enabled and immediately starts counting up. It
is not possible to affect the content of the STM during normal operation of the TC1796.
The timer registers can only be read but not written to.
The STM can be optionally disabled for power-saving purposes, or suspended for
debugging purposes via its clock control register. In suspend mode of the TC1796
(initiated by writing an appropriate value to STM_CLC register), the STM clock is
stopped but all registers are still readable.
Due to the 56-bit width of the STM, it is not possible to read its entire content with one
instruction. It needs to be read with two load instructions. Since the timer would continue

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

ABB ControlMaster CM15 Commissioning Instructions preview
ControlMaster CM15
Brand: ABB Pages: 28
7th Sense medialon Showmaster Go User Manual preview
medialon Showmaster Go
Brand: 7th Sense Pages: 2
Barthelme CHROMOFLEX RC Instruction Manual preview
CHROMOFLEX RC
Brand: Barthelme Pages: 8
CAB SHADE User Handbook Manual preview
SHADE
Brand: CAB Pages: 28
C-TEC CAST XFP Commissioning & Programming Quick Start Manual preview
CAST XFP
Brand: C-TEC Pages: 16
C&T Solution MX100 Series User Manual preview
MX100 Series
Brand: C&T Solution Pages: 27
C&K systems SECURIT ST800L+ Installation Manual preview
SECURIT ST800L+
Brand: C&K systems Pages: 16
FAAC E604 Manual For The Installer preview
E604
Brand: FAAC Pages: 60
FAAC E124 Quick Start Manual preview
E124
Brand: FAAC Pages: 12
FAAC E124 Original Instructions Manual preview
E124
Brand: FAAC Pages: 44
FAAC E045 Manual preview
E045
Brand: FAAC Pages: 44
FAAC 844 MPSR Installation Instruction preview
844 MPSR
Brand: FAAC Pages: 8
FAAC B614 Manual preview
B614
Brand: FAAC Pages: 60
FAAC 739 Installation Manual preview
739
Brand: FAAC Pages: 14
FAAC B614 Instruction Manual preview
B614
Brand: FAAC Pages: 68
FAAC 455 D Supplemental Installation Instructions preview
455 D
Brand: FAAC Pages: 16
IAI ROBO Cylinder RCP2 Series Quick Start Manual preview
ROBO Cylinder RCP2 Series
Brand: IAI Pages: 5
Icom IC-706MKII Manual preview
IC-706MKII
Brand: Icom Pages: 30

Brands by name

Popular brands

Load more brands