manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

System Units (Vol. 1 of 2)

LMB External Bus Unit

 

User’s Manual

13-75

V2.0, 2007-07

EBU, V2.0

 

Figure 13-29

 shows a burst read access (burst length of four) with a BFCLKO frequency

of 1/3 of LMBCLK frequency (EXTCLOCK = 01

B

).

Figure 13-29 Burst Flash Read Operation Example (Burst Length of 4)

The lengths of the standard accesses phases during Burst Flash accesses are
programmed as multiples of LMBCLK periods independent of the BFCLKO frequency. It
is the users responsibility to ensure (by programming the access phases accordingly)
that the sampling of data by the EBU guarantees valid sampling of the data from the
Burst Flash device.

13.9.11

External Cycle Control via the WAIT Input

The EBU controls the Burst Flash device via the WAIT input. This allows the EBU to
support operation of Burst Flash while crossing Burst Flash page boundaries. During a
Burst Flash access, the WAIT input operates in one of the five modes shown in

Table 13-20

.

AP

1

AP

2

AP

3

CP

i1

CP

i2

BP

1

BP

2

new

AP1

BP

1

BP

2

CD

i1

CD

i2

CD

i3

BP

1

BP

2

BP

1

BP

2

RP

1

RP

2

LMBCLK

A[23:0]

Addr

MCT05739a

CSx

RD

Data in

Addr. + 0

BFCLKO

ADV

Data in

Addr. + 4

Data in

Addr. + 8

Data in

Addr. + 12

D[31:0]

(32-bit)

Data in

Addr. + 0

Data in

Addr. + 2

Data in

Addr. + 4

Data in

Addr. + 8

BAA

D[15:0]

(16-bit)

Next data 

issued by Flash

Data latched in EBU

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

Eaton AMPGARD RVSS Instruction For Installation And Maintenance preview
AMPGARD RVSS
Brand: Eaton Pages: 16
Haier YR-H71 Service Manual preview
YR-H71
Brand: Haier Pages: 58
Eaton COOPER POWER SERIES Installation And Operation Instruction Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 50
Hanna Instruments HI 8001 Instruction Manual preview
HI 8001
Brand: Hanna Instruments Pages: 88
Hama Black Force Wireless Operating Instruction preview
Black Force Wireless
Brand: Hama Pages: 10
tams elektronik ABC-1 Manual preview
ABC-1
Brand: tams elektronik Pages: 12
Waterway NEO 1200 Instruction Manual preview
NEO 1200
Brand: Waterway Pages: 8
B&G ZEUS S Detailed App Manual preview
ZEUS S
Brand: B&G Pages: 19
Haberl Electronic 1E0671-1 MCR2.9 User Manual preview
1E0671-1 MCR2.9
Brand: Haberl Electronic Pages: 9
J+J J4C Series Installation Instructions preview
J4C Series
Brand: J+J Pages: 2
PUTCO 8770HF Installation preview
8770HF
Brand: PUTCO Pages: 2
OPW PetroVend PV200 Options Installation preview
PetroVend PV200
Brand: OPW Pages: 2
Game ready Equine 550250 User Manual preview
Equine 550250
Brand: Game ready Pages: 24
Linak TR-EM-288-SPF Quick Manual preview
TR-EM-288-SPF
Brand: Linak Pages: 2
EFI E-42 Installation And Service Manual preview
E-42
Brand: EFI Pages: 127
maxxess eMAX-EP4502 Installation Manual preview
eMAX-EP4502
Brand: maxxess Pages: 11
SOLARJACK PVA 5-30 User Manual preview
PVA 5-30
Brand: SOLARJACK Pages: 14
BABYTREND Expedition Double Jogger Instruction Manual preview
Expedition Double Jogger
Brand: BABYTREND Pages: 18

Brands by name

Popular brands

Load more brands