manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

System Units (Vol. 1 of 2)

System Control Unit

 

User’s Manual

5-61

V2.0, 2007-07

SCU, V2.0

 

5.12

SCU Registers and Address Map

This section refers to all registers which are located in the SCU address range. Some of
these registers are described in other chapters of this User’s Manual. The entries in
column entitled “Description see” of 

Table 5-9

 point to the pages on which such registers

are described in detail.

Figure 5-14 SCU Registers

The complete and detailed address map of all SCU registers is described in 

Table 18-3

on 

Page 18-7

 of the TC1796 User’s Manual System Units part (Volume 1).

Table 5-9

SCU Registers

Register Short 
Name

Register Long Name

Offset 
Address

Description 
see

SCU_ID

SCU Module IDentification Register

08

H

Page 5-69

SCU_SCLKFDR SCU System Clock Fractional Divider 

Register

0C

H

Page 3-42

RST_REQ

Reset Request Register

10

H

Page 4-5

RST_SR

Reset Status Register

14

H

Page 4-3

MCA05625_mod

Identification 

Registers

MANID
CHIPID
RTID

OSC_CON
PLL_CLC
SCU_SCLKFDR
RST_SR
RST_REQ

Clock  / PLL /Reset  

Registers

External Trigger 

Register

EICR0
EICR1
EIFR
FMR
PDRR
IGCR0
IGCR1
TGADC0
TGADC1

SCU_CON
SCU_STAT

Miscelleaneous 

Registers

SCU_SCLIR

SCU_TCCON
SCU_TCLR0

Port Control 

Registers

PMG_CSR

Power Management  

Register

NMISR

SCU_TCLR1
SCU_EMSR

SCU_PTCON
SCU_PTDAT0

Pad Test Mode 

Registers

SCU_PTDAT1
SCU_PTDAT2
SCU_PTDAT3

Watchdog Timer 

Registers

WDT_CON0
WDT_CON1
WDT_SR

SCU_ID

SCU_PETCR
SCU_PETSR

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

DAV TECH DA 250 Installation And Maintenance Manual preview
DA 250
Brand: DAV TECH Pages: 10
Aalborg SMV Operating Manual preview
SMV
Brand: Aalborg Pages: 15
Aalborg DFC Operating Manual preview
DFC
Brand: Aalborg Pages: 48
Eaton PKE-COM-RTU Instruction Leaflet preview
PKE-COM-RTU
Brand: Eaton Pages: 2
Eaton i-on30R Installation Instructions preview
i-on30R
Brand: Eaton Pages: 2
Eaton MEMSHIELD 4 Installation Instructions Manual preview
MEMSHIELD 4
Brand: Eaton Pages: 8
GARAN EWS-102 Calibration & Setup preview
EWS-102
Brand: GARAN Pages: 8
Gamma Vacuum SPCe User Manual preview
SPCe
Brand: Gamma Vacuum Pages: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Brand: Gamma Pages: 28
Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Brand: Parker Pages: 44
Gatekeeper ITSS User Manual & Install Manual preview
ITSS
Brand: Gatekeeper Pages: 28
jbc DDE-1B Manual preview
DDE-1B
Brand: jbc Pages: 44
jbc SKR Instruction Manual preview
SKR
Brand: jbc Pages: 8
Ziton ZP1-X3E Series Operation Manual preview
ZP1-X3E Series
Brand: Ziton Pages: 36
Cypress CY3280-BK1 Quick Start Manual preview
CY3280-BK1
Brand: Cypress Pages: 3
INSBUD IB-TRON 4000 SOL Instruction Manual preview
IB-TRON 4000 SOL
Brand: INSBUD Pages: 14
babyplus CompactTWIN Assembly & Operating Instructions preview
CompactTWIN
Brand: babyplus Pages: 28
Sartorius PR 5610 Installation Manual preview
PR 5610
Brand: Sartorius Pages: 165

Brands by name

Popular brands

Load more brands