manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

Peripheral Units (Vol. 2 of 2)

Micro Second Channel (MSC)

 

User’s Manual

21-21

V2.0, 2007-07

MSC, V2.0

 

21.1.3

Upstream Channel

The MSC upstream channel is an asynchronous serial receiver based on the standard
asynchronous data transfer protocol. It is dedicated to receive a serial data stream from
a peripheral device via its serial data input SDI, using two specific data frame formats.

Figure 21-14

 is a block diagram of the MSC upstream channel.

Figure 21-14 Upstream Channel Block Diagram

The incoming data at SI is sampled after it has been filtered for spikes. The detected
logic states of the serial input are clocked into a shift register. After the complete
reception of the serial data frame, the content of the shift register is transferred into one
of the four data registers, and an interrupt can be generated optionally.
The receive baud rate is directly coupled to the module clock 

f

MSC

, and can be within a

range of 

f

MSC

/4 up to 

f

MSC

/256.

Upstream Data Registers

Serial Receive Buffer

Upstream

Channel

Control

RDI

SDI[7:0]

f

MSC

MCB05808

Samp-

ling

UD0
UD1
UD2
UD3

Shift Register

Spike

Filter

SI

Input Control

Interrupt

SDI

M

U

X

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

E-fly 100C Operating Manual preview
100C
Brand: E-fly Pages: 16
KEENZ Class Instruction Manual preview
Class
Brand: KEENZ Pages: 24
Samson 2406 Mounting And Operating Instructions preview
2406
Brand: Samson Pages: 32
Quantum FX Instruction Booklet preview
FX
Brand: Quantum Pages: 15
Saga SAGA1-L40 User Manual preview
SAGA1-L40
Brand: Saga Pages: 9
H3C S9500E Series Card Manual preview
S9500E Series
Brand: H3C Pages: 5
H3C WX1800H series Command Reference Manual preview
WX1800H series
Brand: H3C Pages: 27
H3C WX3500H series Installations preview
WX3500H series
Brand: H3C Pages: 4
H3C WX5540H Installation Manual preview
WX5540H
Brand: H3C Pages: 54
H3C LSWM1WCM10 Manual preview
LSWM1WCM10
Brand: H3C Pages: 10
H3C LSQM1WCMB0 Quick Start Manual preview
LSQM1WCMB0
Brand: H3C Pages: 10
IDS X64 Manual preview
X64
Brand: IDS Pages: 2
WAM LBC Series Assembly And Main Instructions For Use And Maintenance preview
LBC Series
Brand: WAM Pages: 62
walimex WR-100 Instruction Manual preview
WR-100
Brand: walimex Pages: 7
Walchem WebMaster Manual preview
WebMaster
Brand: Walchem Pages: 2
Walchem WebMaster Quick Start Manual preview
WebMaster
Brand: Walchem Pages: 73
Walchem W900 Series Instruction Manual preview
W900 Series
Brand: Walchem Pages: 126
wallas 3008 Quick Start Manual preview
3008
Brand: wallas Pages: 2

Brands by name

Popular brands

Load more brands