Inficon Sensistor Sentrac Service Instructions Manual Download Page 34

Page: 34 / 76

5 | Service Instructions

INFICON

34 / 76

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

5.6 Changing Battery (Portable Model)

Part

Part no.

Qty

Consumables

Battery Li-Ion 14,

591-782

Disassemble

Disconnect the mains connector.

Remove the cover, see Disassemble in Remove the Cover [

}

28].

Remove the two screws (C) holding the power switch panel.

Remove the four screws (A) holding the Battery (B).

Remove the Battery (B).

Remove the Battery cabling from the power switch panel and main PCB.

Assemble

Install the new Battery.

Mount the Battery cabling according to drawing below.

Reinstall and tighten the four screws (A) holding the Battery.

Reinstall the cover, see Assemble inRemove the Cover [

}

28].

Summary of Contents for Sensistor Sentrac













































































Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands

Inficon Sensistor Sentrac, Service Instructions Manual

Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands