background image

Additional Information 

For installation instructions see Install Guide.
For compressor package wiring diagram contact manufacturer.
For compressor parts breakdown see website (compressed-air-systems.com) of contact  

compressor manufacturer.
On electric driven compressors always follow NEC (National Electric Code) on any local applicable code 

that exceeds NEC guidelines.
On gas/diesel engine driven packages follow engine manufacturer guide for proper placement  

and installation of engine driven equipment.

WARNING: 

Always wear proper protective eye ware, hearing protection and safety clothing when 

working around the compressor package. No loose or baggy clothing should be worn around  

compressor package at any time.

WARNING:

 On Electric motor powered air compressors make sure electrical system is up to National 

Electric Code (NEC) prior to installing compressor system. Failure to install a compressor with a proper 

NEC electrical system can cause personal injury, compressor package damage and void compressor 

package warranty

NOTICE: 

To ensure full compressor tank warranty all tank mounted compressor packages must be 

mounted on factory approved vibration isolation pads. A compressor should NEVER be installed while 

still on or in its original packaging. Failure to properly install the compressor system with approved 

vibration isolation pads will result in the compressor tank warranty being void.

WARNING:

 Compressed Air Systems compressors can operate at pressures from 0-250psi depending 

on the compressor package design and build specifications. Always verify that the system the  

compressor is installed into can handle the maximum operational pressure the compressor. NEVER 

install a compressor in a system that can not handle the compressors maximum operating pressure.

WARNING:

 Compressed air is extremely dangerous when not properly used or installed. Always make 

sure a trained compressed air professional has looked over the air system prior to use. Improper  

installation or use of compressed air can cause bodily injury or death. NEVER pressurize an object that 

was not designed to be pressurized. Pressurizing objects not properly engineered for the maximum  

operating pressure of the compressor system can cause bodily injury or death.

Industrial Gold Air Compressors  

|

 800-531-9656  |  www.industrialgold.com

G43 Pump

Summary of Contents for G43





















Reviews: