Indesit UIAA 1x.1 Series, Operating Instruction

Page: 5 / 12

GB
5
Installation
! Before placing your new appliance into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the
appliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of
the appliance and any furniture above it, and at least 5 cm
between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat
(direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied in
the installation kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator
by tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical
socket ensure the following:
• The appliance is earthed and the plug is compliant with the
law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on
the bottom left side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values
indicated on the data plate located on the bottom left side
(e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use
extension cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
!
The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
! The manufacturer declines any liability should these
safety measures not be observed.
! Installation of the device will be carried out by authorized
service.
Start-up and use
Starting the appliance
! Before starting the appliance, follow the installation
instructions (see Installation).
!
Before connecting the appliance, clean the compartments
and accessories well with lukewarm water and bicarbonate.
1. Insert the plug into the socket and ensure that the red
ALARM and green POWER indicator lights illuminate (the
TEMPERATURE ADJUSTMENT knob must not be on ).
2. When the red indicator light switches off, turn the
TEMPERATURE ADJUSTMENT knob to a medium position.
The freezer is now ready to be used.
Using the freezer to its full potential
• Use the FREEZER OPERATION knob to adjust the
temperature (see Description).
• Do not re-freeze food that is defrosting or that has already
been defrosted. These foods must be cooked and eaten
(within 24 hours).
• Fresh food that needs to be frozen must not come into
contact with food that has already been defrosted. Fresh
food must be stored in the top FREEZER and STORAGE
compartment where the temperature drops below -18°C and
guarantees rapid freezing.
• Do not place glass bottles which contain liquids, and which
are corked or hermetically sealed in the freezer because
they could break.
• The maximum quantity of food that may be frozen each day
is indicated on the data plate, which is located inside the
freezer (for example: 4 kg per 24 hours).
• In order to obtain a greater amount of space in the freezer
compartment, you may remove the bins (except the lowest
bin) and place the food directly onto the evaporator plates.
! Do not open the door during freezing.
! If there is a power cut or malfunction, do not open the freezer
door. This will help maintain the temperature inside the freezer,
ensuring that foods are conserved for at least 9 -14 hours.
!
Warning Indicator Light. When this red warning light comes
on for a prolonged period of time, it means that the freezer is
not functioning properly and the temperature is rising too much.
(Call your Service Centre).
This warning light might come on for a brief period when:
a) the door is left open for an extended period of time (when
the freezer is being loaded or unloaded).
In these two cases, the fact that the warning light comes on
does not indicate that the freezer is malfunctioning or there is a
defect.
Ice
3
ice tray
*
The fact that they are situated on the top part of the freezer
drawers ensures greater cleanliness: the ice no longer
comes into contact with the food placed inside the freezer
compartment; furthermore, the dripping of the water during
filling is avoided (a lid to cover up the hole after filling with
water is also provided).
1. Pull out the tray by pushing it up. Check that the tray is
completely empty and fill it with water through the opening
provided.
2. Take care not to exceed the level indicated (MAX WATER
LEVEL). Excess water prevents the ice cubes from
dispensing (if this happens, wait for the ice to melt and
empty the tray).
3. Turn the tray 90°: due to the connected compartments each
mould fills with water (see diagram).
4. Close the opening with the lid provided and put the tray
back, placing the top part in the corresponding housing and
allowing it to drop in again.
5. When the ice has formed (minimum time approximately 8
hours) knock the tray against a hard surface and wet the
outside so that the ice cubes come loose and take them out
through the opening.
*
Varies by number and/or position, available only on certain
models.