background image

8

GB

Dishwasher delayed start programming

Premise: before selecting a wash cycle as indicated in the
paragraph entitled "Starting and setting a wash cycle…", a
delayed start can be set.

Press button "

D

" (see close-up view "control panel") to delay

the start of a wash cycle by 1 to 24 hours. Each time you
press the button, the counter "

L

" will display the number of

hours the cycle start has been delayed by in sequence; choose
the time you prefer.
The delayed start indicator light "

H

" flashes and when the

appliance starts, the counter will begin the countdown to
the delayed start.
When this time is up, the wash cycle will begin and the
counter will now serve to display the amount of time left
until the end of the wash cycle.

NOTE:

n

it is best if you keep from modifying anything during

countdown; if this is absolutely necessary, then turn the knob
to the RESET position: 4 beeps and the 3 dashes appearing
indicate that all settings have been cancelled
Repeat the operations for "dishwasher delayed start
programming" and for "starting and setting the wash cycle"
following the instructions in the relative paragraphs.

n

Should there be a power failure or should the door of

the appliance be opened during the countdown, the latter
will come to a stop and will re-start either when the power
comes back on or when the door is closed.

Dishwasher delayed start programming

Wash cycle modification buttons

Half load selection button on upper or lower rack.

This can be selected before setting any wash cycle, yet we
remind you that you should 

halve the amount of detergent

recommended for the wash cycle you have selected (see
wash cycle table).

Press button "

I

" and you will hear a beep, the indicator "

N

"

appears on the display: you can select which rack to perform

the half load on. Each time the button is pressed, you will

hear a beep, and symbol  

   appears indicating the wash

on the upper rack, whereas symbol  

  indicates the wash

on the lower rack. Press the button again and you will hear

another beep, thereby resetting the selection and the

appliance will consequently wash on both racks.

To use the racks correctly, we recommend you read the

chapter entitled "Loading the dishes".

Summary of Contents for DE 73

















Reviews: