background image

Attach the INCRA Jig Ultra to base

support panel and loosely attach

remaining base clamp

Open the Ultra Mounting Hardware Pack.  Place #10 washers
on each of the (6) #10-32 x 

1

/

2

" phillips pan head screws.  Insert

four of the screws through the slotted holes on the Ultra base
and loosely thread a #10-32 hex nut onto each screw.  Insert
the remaining two screws through the two inside holes located in
the middle of the Ultra’s base and attach hex nuts.  Slide the
hex nuts on all six screws into the T-slots on the base support
panel.  The (4) screws/nuts in the slotted holes slide into the
outer T-slots.  The (2) screws/nuts inside the Ultra’s base slide
into the inner T-slots.  See 

  and  .

Center the Ultra’s base on the support panel.  (Edge of Ultra
should be about 10

5

/

8

" from end of panel.)  Use a square to

align the Ultra base at 90° to the panel and
tighten the screws installed in the slotted
holes only.  Do not tighten the two screws
inside the Ultra’s base at this time.  Slide
the hex nuts on the remaining base clamp
into the T-slots on the support panel.

4

Attach one base clamp to end of

base support panel

Open the Base Mount & Fence Glide Hardware Pack.  Insert
the (8) #10-32 x 

7

/

16

" phillips flat head screws in the

countersunk holes of both base clamps and loosely thread on
the #10-32 hex nuts.  Slide the hex nuts on one of the base
clamps into the (4) T-slots on the base panel. 

 .  Leave

about 

3

/

8

" between the panel end and the vertical surface on

the base clamp as shown in 

  and tighten the

screws.  Set aside the
remaining fasteners from
the Base Mount & Fence
Glide Hardware Pack 
for
use in 

  and  on

page 8.

Remove

endcaps

from base

support panel

See 

  at right.

BASE MOUNT ASSEMBLY

Attach glide pads to underside of

base clamps 

Peel the adhesive backing from the glide pad and adhere to the
base clamp as shown in 

 .  Repeat for remaining base clamp.

1

2

FIG. 9

Adhere glide pad to

underside of base clamp

Adhesive

backed glide pad

Base clamp

FIG. 11

Attach one base

clamp to end of

base support panel

Do not tighten these two

screws at this time

Base support panel

Screws inside ULTRA base – use inner T-slots

 The base support panel used in the base mount

assembly is designed for use with table saws having a front
to back measurement of up to 28".  If your table saw

measures greater than 28" a custom cut support panel is
available.  For details, e-mail us at [email protected] or
call us at the number listed at the bottom of page 12.

Endcap

FIG. 10

Base

clamp

FIG. 12

Attach ULTRA to

base support panel

10 

5

8

"

INCRA Woodworking Tools & Precision Rules

6

#10– 32 x 

7

16

"

phillips flat head screw

#10-32

hex nuts 

Base support

panel

3

Hex nuts for screws

captured in T-slots

on support panel

Screws in slotted 

holes – use outer T-slots

Detail 11A

Base support panel

3

8

"

Base clamp

Detail 12A

Note:  Do not attach glide pads until after main rail
installation has been completed. (See page 5, Figs. 4 and 5).

Base support

panel

Base clamp

Base support

panel

Machinist square

#10– 32 x 

1

2

" phillips pan

head screws with washers 

Summary of Contents for TS III













Reviews: