background image

Table 1

 

LINKING

 

The  translator  /  expander  module  is  waiting  to  achieve  a  wireless  child 
device.

 

1)

 

Move  the  link  switch’s  cursor  from  ON  to  the  opposite  side  (BLANK 
side); 

HFW

-

SIM

-

01

-

AS

 indicates “Linking to the system”.

 

2)

 

If linking outcome is ok: 

HFW

-

SIM

-

01

-

AS

 stops indicating “Linking to 

the 

 

system”.

 

3)

 

If linking outcome is not ok: perform the 

LINKING RECOVERY

 

procedure.

 

LINKING RECOVERY

 

In case something goes wrong with the linking operation:

 

1) Take out both batteries from their holders.

2) Move alternatively the link switch to ON / BLANK five times.

3) Move the link switch to ON.

 

4) Reinsert both batteries into their holders, oriented as per polarity marks.

5) Perform the 

LINKING

 procedure.

 

 

WIRELESS LINK QUALITY CHECK

 

It is possible to check wireless link quality between the sounder module and its linked

-

to translator or expander in this way: 

 

1)

 

Move the link switch to the ON position.

2)

 

Module’s LED indicator will start blinking according to the following table:

3)

 

Move the link switch to position BLANK again; 

device will NOT WORK if the link switch is on position ON !

LINK SWITCH

 

LED INDICATOR

 

Picture 4

 

During all the duration of the linking 
phase,  the  module  must  be  only  a 
few  inches  away  from  the  transla-

tor / expander module you are linking to.

 

LINK QUALITY

 

EVALUATION

 

DEVICE’S INDICATION

 

No connection

 

Fail

 

Two red blinks

 

Link margin is less than 10 dB

 

Poor

 

One red blink

 

Robust communication with link margin from 10 dB to 20 dB

 

Good

 

One green blink

 

Robust communication with link margin over 20 dB

 

Excellent

 

Two green blinks

 

Table 2

 

MODULE’S STATUS

 

GREEN LED

 

RED LED

 

Power up

 

1 second green, then 0.5 second red for 4 times

 

Linking to the system

 

Blinking until linking is 

completed

 

Normal condition

 

Main battery fault

 

0.5 second on and

 

10 seconds off

 

(orange tonality)

 

Secondary battery fault

 

0.5 second on and

 

10 seconds off

 

-  

Both batteries fault

 

0.5 second on and

 

10 seconds off

 

(orange tonality)

 

Lost link with wire to wireless 
translator / wireless expander

 

0.5 second green and red (amber) and

 

1 second off

 

Summary of Contents for HFC-SBR-23-03












Reviews: