background image

 

air gun. Heat activates the glue, providing an instant and permanent bond. Work down 
with a hard tool, applying pressure to the patch while warm. 
 

Temporary

 repairs can be effected without heat or solvent if the patch is applied before 

one of the glued surfaces is dry, i.e. while still slightly tacky.  
 
Note:  Factory repairs use the same adhesive 

with the addition of an activator

. This has 

the effect of greatly increasing bond strength, resistance to heat and resistance to wa-
ter. It has limited shelf life. Supplies of activator in New Zealand are obtainable from In-
cept. Otherwise visit <http://www.incept.co.nz/inflatable_rafts_FAQ2.htm>.  

 

 

10. Warranty 

INCEPT inflatable boats are guaranteed for a period of five years in non-commercial use. 
Any defects in materials or workmanship found during that period will be made good by 
Incept Marine Ltd at no cost, provided only that the boat is returned to the Taihape NZ 
factory or the nearest authorised repair depot, freight paid.  
 
Warranty is not transferable with boat ownership. Damage to internal baffles caused by 
tampering with the pressure relief valves are not covered by warranty.  
 
 
 

11. Safety on water 

 

CAUTION 
 
PADDLESPORTS / WATERSPORTS CAN BE VERY DANGEROUS AND PHYSICALLY 
DEMANDING.

 The user of this product should understand that participation in Paddle-

sports / Watersports may involve serious injury or death. Observe the following safety 
standards whenever using this product. 
 
Get Paddlesports / Watersports instruction specific to this type of craft. 
Obtain certified first aid training and carry first aid and rescue/ safety equipment. 
Always wear a nationally approved personal flotation device. 
Always wear a helmet where appropriate. 
Dress appropriately for weather conditions; cold water and/ or cold weather can re-

sult in hypothermia. 

Check your equipment prior to each use for signs of wear or failure. 
Never paddle / go boating alone. 
Do not paddle in flood conditions. 
Be aware of appropriate river water levels, tidal changes, dangerous currents and 

weather changes. 

Scout unfamiliar water; portage where appropriate. 
Do not exceed your paddling ability; be honest with yourself. 
Consult your physician prior to beginning your Paddlesports training. 
You must not use alcohol or mind-altering drugs prior to using this product. 
Follow the manufacturer's recommendations for the use of this product. 
If additional outfitting is required, use manufacturer's approved materials only;  

do not impair entry or exit access. 

7 (8) 

Summary of Contents for Stowaway S24K









Reviews: