Inateck BCST-53 Instruction Manual Download

Page: 9 / 65

Buzzer
Sounds

Explanations

One short high-note sound (100ms)

Successful scanning

Two or more long high-note sound
(800ms)

The USB is under configuration

Three-note chord
(volume from low to high)

Enter setup mode (blue LED lit)
Exit setup mode (blue LED off)

Two short sounds
(volume from low to high)

Indicate correct settings

Barcodes Supported
The barcode types supported by the BCST-53 can be found in the chart below. For
more details, please refer to the barcode type setting in Barcode Type Setting.
Barcodes Supported

Preset

Codabar

Enabled

Code 11

Disabled

Code 128

Enabled

GS1-128 (UCC/EAN-128)

Disabled

USPS

Enabled

FedEx

Enabled

Code 39

Enabled

Code 32

Disabled

Code 93

Enabled

EAN-8

Enabled

EAN-13

Enabled

ISBN

Disabled

ISSN

Disabled

MSI

Disabled

UPC- A

Enabled

UPC- E

Enabled

2 of 5 barcodes IATA 2 of 5

Disabled

Summary of Contents for BCST-53


































































Search results

Summary of Contents for BCST-53

Reviews:

Related manuals for BCST-53

Brands by name

Popular brands

Inateck BCST-53, Instruction Manual

Search results

Summary of Contents for BCST-53

Reviews:

Related manuals for BCST-53

Brands by name

Popular brands