background image

23

SB-LED | Indoor

WWW.SB-RAILING.COM

5  MAINTENANCE 

DANGER

Always switch off power to the product before performing any work.

 

ƒ

Check the functioning of the LED strips and the fixation of the handrail brackets or baluster adapters once a year.

 

ƒ

Clean the stainless steel parts of the handrail with a suitable cleaning product.

 

ƒ

For periodic cleaning of plastic cover caps, wipe them carefully with a dry or lightly moistened cloth. 

 

ƒ

Avoid using too much water, and do not use solvents or cleaning products containing bleach. Do not use abrasive 
or corrosive products. 

6  THE ENVIRONMENT AND DISPOSAL

This symbol on the material, the accessories or the package indicates that the product should not be 
treated as household waste. For disposal, take the device to a collection point for the recycling of used 
electrical and electronic devices within the EU and in other European countries which have separate 
collection systems for used electrical and electronic devices. By disposing of the device properly, you help 
avoid potential hazards to the environment and public health that might otherwise be caused by improper 
handling of the discarded device. Recycling of materials helps to conserve natural resources. This is why 

you should not dispose of used electrical and electronic devices in household waste.

   

7  WARRANTY AND DISCLAIMER

Request the complete and current warranty conditions from SB-Railing or consult www.illunox.com.

Disclaimer

 

ƒ

SB-Railing cannot be held responsible for any loss or damage caused by improper use or misuse. 

 

ƒ

Subject to change without prior notice. Visit www.illunox.com for the latest version of the guide.

 

ƒ

No rights can be derived from this guide.

Summary of Contents for SB-LED

























Reviews: