background image

 

 

Please  read  these  instructions,  it  includes  important  information  about  the 
installation, usage and maintenance of this product. 

 

Warning!  Verify  that  the  voltage  select  switch  on  your  unit  matches  the  line 
voltage applied. Damage to your fixture may result if the line voltage applied 
does not match the voltage indicated on the voltage selector switch. All fixtures 
must be connected to circuits with a suitable Earth ground. 

 

1. Preface

   

1.1 Packing list 

 

Product name 

quantity 

moving head light 

1 pcs 

Power -line 

  1 base 

User manual 

1pcs 

 

1.2 Unpacking instructions

   

 
On  receiving  a  fixture,  carefully  unpack  the  carton,  check  the  contents  to 
ensure  that  all  parts  are  presented,  and  have  been  received  in  a  good 
condition.  Notify  the  shipper  immediately  and  retain  packing  material  for 
inspection  if  any  parts  appear  damaged  from  shipping  or  the  carton  itself 
shows, sign of mishandling. Save the carton and all packing materials. In the 
event  that  a  fixture  must  be  returned  to  the  factory,  it  is  important  that  the 
fixture should be returned in original factory box and packing. 
 

1.3 AC Power 
 

To  determine  the  power  requirements  for  a  particular  fixture,  see  the  label 
affixed  to  the  back  plate  of  the  fixture  or  referred  to  the  fixtures  specification 
chart.  A  fixture  listed  current  rating  is  its  average  current  draw  under  normal 
conditions.  All  fixtures  must  be  directly  powered  off  a  switched  circuit  and 
cannot  be  run  off  a  rheostat  (variable  resistor)  or  dimmer  circuit,  even  if  the 
rheostat  or  dimmer  source  voltage  matches  the  fixtures  requirement.  Check 
the  fixture  or  device  carefully  to  make  sure  that  if  a  voltage  selection  switch 
exists that it is set to the correct line voltage you will use. 
 
 
 
 
 

 
1.4 Safety instructions 

 
 
 
Please  keep  this  user  guide  for  future  consultation.  If  you  sell  the  unit  to 
another user, be sure that they also receive this instruction booklet. 
Always make sure that you are connecting to the proper voltage, and that the 

Summary of Contents for IM-MH90S











Reviews: