The tico 731.2 is a battery powered LCD-counter with programmable
count input for contact or edge triggering. The following versions are
available:
standard
special
Totalizer:
0 731 201
0 731 721
Tachometer (1/min):
0 731 202
0 731 722
Time counter (HHHH:MM:SS):
0 731 203
0 731 723
Time counter (HHHHHHH.HH):
0 731 204
0 731 724
Numeric PLC-display:
1
0 731 205
0 731 725
or with plug in screw terminal e. g. 0 731 201 S
1. Programming of the COUNT-Input (all versions)
In order to match your application, the COUNT-Input can be
programmed for high speed (7,5 kHz) or low speed counting (30 Hz
attenuated). Positive or negative edge is programmable as well.
NOTE:
The counter leaves the factory with the default value HI PNP
(f
max
7,5 kHz and positive edge triggered) and unlocked key.
To change the count input configuration:
2. Totalizer version (0 731 201)
Terminal 4 „RESET or Tacho-HOLD“ is defined as the Reset-Input.
3. Tachometer version (0 731 202)
The tachometer operates via the gate measuring method. Within the
measuring time of 6 sec, the incoming pulses are counted and recal-
culated in order to display 1/min.
The Terminal 4 „RESET or Tacho-HOLD“ is defined as the HOLD-Input
(as long as this Input is active, the actual value in the display is
frozen).
4. Time counters versions (0 731 203 and 204)
The time counters will count as long as the Count-Input (3) is active
(this can be a low or a high signal according to programming in
Chapter 1).
Terminal 4 „RESET or Tacho-HOLD“ is defined as Reset-Input.
5. Terminal connection
Totalizer, Tacho, Time counters
Numeric PLC-Display
1
6. Specifications
Power supply
Terminal 1 and 2; 12..24 VDC
Tolerances: +20 -10%
Current consumption
5 mA, external overvoltage
protection 0,035 AT
Data retention
non volatile RAM (NV), >10 years
Display
LCD, 8-digit, 7 mm
Count input
Terminal 3 „Count“
active edge
programmable: NPN: negative
(e.g. Contact to ground 0V) or
PNP: positive signal
pulse length: min 70µs or
min 15 ms (if attenuated to 30 Hz )
Count frequency
programmable:
„HI“ 7,5 kHz or „LO“ 30 Hz
(attenuated for Contacts)
Amplitude threshold
< 0,7 V and > 5 V, max 30 VDC
Reset input or
Reset with a negative edge on
tacho hold
„RESET“, (Terminal 4 bridge to
Ground, 0V)
pulse length: min 15 ms
(attenuated to 30 Hz )
Key reset
press front key shortly
Keylock
programmable see chapter 1
Mounting
Frontpanel mounted with clamping
frame
Front dimension
DIN 48 mm x 24 mm
Panel cut-out
45
+ 0,6
mm x 22
+ 0,3
mm
Panel thickness
max. 14 mm
Product depth
32 mm
Protection class
front side IP 54
Operating temperature
-10° C to +50°C
Storage temperature
-20° C to +60°C
General rating
DIN EN 61010 part 1, VDE 0411 part 1
Protection class
according to class II
Overvoltage
category II
Contamination
level 2
Operating instructions tico 731.2
- DC powered LCD-Counter
to confirm the desired value
to confirm the desired value
press button longer (> 2 sec)
press button longer (> 2 sec)
Note:
Maximum count speed
(7,5 kHz) and negative
edge triggered
Note:
Maximum count speed
(7,5 kHz) and positive
edge triggered
Note:
low count speed (30 Hz
attenuated) and negative
edge triggered (e.g.
contacts)
Note:
low count speed (30 Hz
attenuated) and positive
edge triggered (e.g.
contacts)
Note:
front key is locked
Note:
front key is unlocked
*default values
hold down the front key
and switch power on
press button shortly
press button shortly
press button shortly
press button shortly
to changes values
**not applicable to time counters
Zählmodus
Count Mode
Zählmodus
Count Mode
**
*
*
1
There is an extra operating instruction (No. 2 731 022) with protocol description for the numeric PLC-display.
2/6
Sach-Nr. 2 731 021; Version 1230699MW
