background image

RShell Reference Manual 

 

 

34

.

 

  

Proprietary and Confidential

 

Revision 4.2, Copyright © 2009, Impinj, Inc. 

Table 4-37 Show Network DNS Response Parameters 

Argument 

Format 

Description 

Domain<n>Static 

string 

Statically configured domain (if configured) 

Domain<n>Dynamic  string 

DNS domain obtained from DHCP (if available) 

Server<n>Static 

ip address

Address of the Nth static DNS server 

Server<n>Dynamic 

ip address

Address of the Nth dynamic DNS server 

Table 4-38 Show Network ICMP Response Parameters 

Argument 

Format

Description 

icmpInMsgs  

integer 

See MIB-2 RFC 1213 

icmpInErrors  

integer 

 

icmpInDestUnreachs 

 

integer 

 

icmpInTimeExcds  

integer 

 

icmpInParmProbs  

integer 

 

icmpInSrcQuenchs  

integer 

 

icmpInRedirects  

integer 

 

icmpInEchos  

integer 

 

icmpInEchoReps  

integer 

 

icmpInTimestamps  

integer 

 

icmpInTimestampReps  

integer 

 

icmpInAddrMasks  

integer 

 

icmpInAddrMaskReps  

integer 

 

icmpOutMsgs  

integer 

 

icmpOutErrors  

integer 

 

icmpOutDestUnreachs  

integer 

 

icmpOutTimeExcds  

integer 

 

icmpOutParmProbs  

integer 

 

icmpOutSrcQuenchs  

integer 

 

icmpOutRedirects  

integer 

 

icmpOutEchos  

integer 

 

icmpOutEchoReps  

integer 

 

Summary of Contents for RShell


















































Reviews: