Impex MWM-981 Owner'S Manual Download Page 18

 

STEP 8   (See Diagram 8 & Cable Loop Diagram) 

 

A.)  Attach the 164” Lower Cable (#33) to the open bracket on the Base Frame (#3).  
B.)  Attach a Pulley (#35) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt 

(#62), two 

 ¾” Washers (#73), and one M10 Aircraft Nut (#70). 

C.)  Draw the Cable underneath the Pulley then pull upward towards the Double 

Floating Pulley Brackets (#13) installed in Step-6. 

D.)  Attach a Pulley to the selected hole on the Brackets. Secure it with one M10 x 1 

¾” Allen Bolt (#62), two Cable Retainers (#29), and one M10 Aircraft Nut (#70). 

E.)  Draw the Cable around the Pulley then downward to an open bracket on Base 

Frame. Repeat B to install a Pulley. 

F.)  Draw the Cable around the Pulley and pull the Cable upward to the Angled 

Double Floating Pulley Brackets (#16) previously installed in Step-7. Repeat B to 
install a Pulley. 

G.)  Draw the Cable around the Pulley and downward to the open bracket on Base 

Frame. Repeat Procedure B to install another Pulley.  

H.)  Draw the Cable underneath the Pulley through the opening on Vertical Frame 

(#4) to the opening on Vertical Seat Support (#6). Attach a Pulley to the opening. 
Secure it with one M10 x 2 ½” Allen Bolt (#66), two Ø 1” x Ø 5/8” Pulley Bushings 
(#57), and one M10 Aircraft Nut (#70). 

I.) 

Draw the Cable underneath the Pulley to the bracket on the Leg Developer (#7).  
Secure the end of Cable to the bracket with one M10 x 1” Allen Bolt (#64), two Ø 
¾” Washers (#73), and one M10 Aircraft Nut (#70). 

J.)  If the whole Cable system is too loose, adjust the tension of the cable system by 

moving up or down the lower pulley on the Double Floating Pulley Bracket.  
Moving up the pulley up will increase the tension in the pulley system; 
conversely, lowering the pulley will decrease the tension. 

 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

17 

Summary of Contents for MWM-981

























Reviews: