background image

STEP 2 

(See Diagram 2) 

 

A.)  Connect the Front Stabilizer (#42) to the Main Seat Support (#52). Secure them with 

two M10 x ¾” Hex Bolts (#46), four 

 ¾” Washers (#3), and two M10 Aircraft Nuts (#4).  

DO NOT tighten the nuts and bolts yet. Thread the Knob Bolt (#47) into the nut on the 
Front Stabilizer. 

B.)  Connect the Main Seat Support (#52) to the open bracket on the Cross Brace (#11). 

Secure the rear hole on the bracket with one M10 x 2 3/8” Bolt (#2), two 

 ¾” Washers 

(#3), and one M10 Aircraft Nut (#4). Secure the other hole with a 3” Short Lock Pin 
(#58).  Note:  DO NOT over tighten the nut and bolt.  The Main Frame needs to pivot on 
this bolt in able to fold up the bench.  

C.)  Connect one end of Diagonal Support (#43) to the Main Seat Support (#52). Secure it 

with one M8 x 2 1/8” Hex Bolt (#48), two 

 5/8” Washers (#21) and one M8 Aircraft Nut 

(#49). Connect the other end to the Front Stabilizer. Secure it with one M8 x 5/8” Hex 
Bolt (#20) and 

 5/8” Washer (#21). 

D.)  Securely tighten all the nuts and bolts previously installed.  
E.)  Insert a 6 ½” Long Lock Pin (#53) into the hole on the Main Seat Support (52).  NOTE: 

The Pin is not designed to sustain any heavy weight.  Only use the pin when changing 
the backrest board to a vertical position when doing Walk-in-Squat from the rear.   

 

Summary of Contents for Competitor CB 610















Reviews: