background image

20

INS

TALLER

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

3.7  PROGRAMMING THE P.C.B.

The boiler is prepared for possible programming of 

several operation parameters. By modifying these 

parameters as described below, the boiler can be 

adapted according to specific needs.
To access the programming phase, proceed as 

follows (

Fig. 10

):

- press buttons (1) and (2) for 5 about seconds 

until the programming mode is accessed on 

the display;

- using keys (3) and (4), select the parameter to 

be changed indicated in the following table:

- adjust the corresponding value consulting the 

table using keys (5) and (6): first pressure of 

buttons displays the current value;

-  confirm the value set by pressing the Reset but-

ton (1) for about 5 seconds. Only the displayed 

value is saved.

 

Note:

 2 minutes after no button is touched 

will automatically cancel the operation or by 

pressing buttons (1) and (2) simultaneously for 

about 5 seconds. Modified but not confirmed 

values are to be restored to the value preceding 

the modification.

Id 

Parameter

Parameter

Description

Range

(ref. 9 Fig. 2-1)

Default

P00

Solar panels 

selection

The setting of this function is used to set the boiler in order to function with the use 

of solar panels. By setting the parameter P0 in "solar"

on

 mode, the switching off of 

the burner is correlated to the adjustment of the domestic hot water temperature. In 

OFF

 mode, the burner is switched off at maximum value.

on - oF

oF

P01

Gas type selec-

tion

The setting of this function is used to adjust the boiler so that it can operate with the 

correct type of gas

nG - Methane

LG - LPG

Set accord-

ing to the 

gas being 

used

P02

Heating switch-

on delay request 

from room 

thermostat and 

remote control.

The boiler is set to switch-on 3 seconds after the request. In the event of particular 

systems (e.g. area systems with motorised thermostatic valves etc.) it may be neces-

sary to delay ignition

00 - 20  

(00 = 3 seconds

01 = 30 seconds

02 = 60 seconds

20 = 600 sec-

onds)

00

P03

Function  

anti-leakage

This function reduces the heating temperature to 57°C in the case that domestic hot 

water circulation is detected in the heating mode.

on - oF

oF

P04

Domestic hot 

water post circu-

lation function

With the post-circulation function active after domestic hot water withdrawal, the 

pump remains on for 2.5 seconds in winter time and 1.5 seconds in summer time to 

reduce the formation of limestone.

on - oF

on

P05

Minimum CH 

output

The boiler also has electronic modulation that adapts the boiler potentiality to the 

effective heating demand of the house. Then the boiler works normally in a variable 

gas pressure field between the minimum heating output and the maximum heating 

output depending on the system's heating load.

NOTE:

 the boiler is produced and calibrated in the central heating phase at nominal 

output. Approximately 10 minutes are needed to reach the nominal heat output, 

which can be changed using the parameter (P08).

NOTE:

 the selection of the “Minimum heating output” and “Maximum heating out-

put” parameters, in presence of a heating request, allows boiler ignition and power 

supply of the modulator with current equal to the value of the respective set value. 

00 - 70 %

Set 

according 

to factory 

inspection

P06

Maximum CH 

output

00 - 99

(99 = 100%)

99

P07

Central heating 

ignitions timer

The boiler has electronic timing, which prevents the burner from igniting too often 

in central heating mode

01 - 20

01 = 30 seconds 

02 = 60 seconds 

20 = 600 sec-

onds

06

P08

Central heating 

ramp timer

In the ignition phase, the boiler performs an ignition ramp in order to arrive at the 

maximum nominal power set (P06).

01 - 20

01 = 30 seconds 

02 = 60 seconds 

20 = 600 sec-

onds

20

P09

Boiler type

Not used on this model.

01

01

P10

Power 

ignition

Not used on this model.

- - -

- - -

P11

Minimum heat-

ing setting

Defines the minimum flow temperature

35 - 80 °C

35 °C

Summary of Contents for NIKE STAR 24

































Reviews: