background image

17

Kit Description.

The Domus Container kit was designed to fit at least the installation 

space for the Gaudium Solar V2, Trio V2 and Basic Magis Pro kit inside 

the home (not recessed).

The lower part of the frame has levelling feet and holes necessary for 

the hydraulic, gas, electrical, condensate drain and temperature control 

connection.

The back of the frame is provided with special wall fixing brackets.

The upper part, completely open, is designed for the outlet to the flue 

(“B type” and “C type” installations) and the intake duct (only for “C 

type” installation) using the Immergas flue.

Installation operations.

Before installing the Domus Container, it is necessary to remove the front 

door (1) and the fixed casing (2) by loosening the appropriate screws (3).
Release the fixed casing (2) from the stop screws on the frame by 

pushing upwards and at the same time pulling it towards you.

N.B.:

 to remove the front door (1) after having loosened the appropriate 

screws (3), grip the handle (1a) with your left hand and the knob (1b) 

with your right hand.
•  Proceed by levelling the Domus Container using the provided 

levelling feet (4).

•  Make 4 Ø 10 mm holes on the wall in correspondence with the holes 

of the brackets (5).

•  Fix the Domus container on the wall using the Ø10x60 wall plugs 

(6), screws (7) and nuts (8) supplies (Fig. 3).

Attention:

 check that the frame remains in square during the fixing 

operations.

Fig. 3

1

2

3

3

4

4

5

5

5

5

6

6

6

6

3

3

7

7

7

7

8

8

8

8

1b

1a

3

Installation drawings key:

Unique identification of the component 

in the kit

Identification of the component not 

supplied in this kit

1

A

Summary of Contents for 3.022167





























Reviews: