IMG STAGE LINE PARL-174DMX, Instruction Manual

Page: 13 / 58

13
English
•
The heat generated inside the spotlight must be
dissipated by air circulation; never cover the air
vents of the housing .
•
Do not operate the spotlight or immediately dis-
connect the mains plug from the socket
1 . if the spotlight or the mains cable is visibly
damaged,
2 . if a defect might have occurred after the
spotlight was dropped or suffered a similar
accident,
3 . if malfunctions occur .
In any case the spotlight must be repaired by
skilled personnel .
•
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug .
•
For cleaning only use a dry, soft cloth; never use
water or chemicals .
•
No guarantee claims for the spotlight and no
liability for any resulting personal damage or ma-
terial damage will be accepted if the spotlight is
used for other purposes than originally intended,
if it is not safely installed or not correctly con-
nected or operated, or if it is not repaired in an
expert way .
If the spotlight is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment .
3 Applications
This flat LED spotlight is used for illumination, e . g .
on stage, in clubs and ballrooms . As a light source,
seven extra bright 8 W RGBW LEDs are used . Com-
pared to incandescence lamps, they feature a low
power consumption, a low heat generation and a
long life . The LEDs are able to emit coloured light in
the three primary colours (red, green and blue) and
white light, but also light created by additive colour
mixing . Crossfading from one colour to another and
stroboscope effects are also possible .
The unit is designed for control via a DMX light
controller (3, 4, 5, 6 or 8 DMX control channels
available), but it is also possible to operate it on its
own or in combination with several PARL-174DMX
spotlights (master / slave mode) . In addition, the in-
tegrated microphone provides effects in sync with
the music .
4 Installation
When placing the unit, always ensure a sufficient
air circulation during operation . Never cover the air
vents of the housing .
WARNING Install the spotlight safely and ex-
pertly . If it is installed at a place where
people may walk or sit under, it must
additionally be secured (e . g . by a safty
rope at the mounting bracket; fix the safety rope so
that the maximum falling distance of the unit will
not exceed 20 cm) .
1 . Fasten the spotlight via a mounting bracket (1),
e . g . with a stable mounting screw or a support
for lighting units (C-hook) on a crossbar .
To adjust the spotlight, release the two lock-
ing screws (2) on the mounting bracket, adjust
the desired inclination of the spotlight, then
retighten the screws .
2 . Alternatively, place the spotlight as desired
(fig . 1) . Use the mounting brackets as a stand;
position them under the spotlight so that they
will support it . Then fasten the locking screws .
5 Setting the Spotlight
into Operation
WARNING
Never look directly into the light
source for a longer time, this may
cause eye damage .
Please note that fast changes in lighting may trig-
ger epileptic seizures with photosensitive persons
or persons with epilepsy!
Connect the mains cable provided to the mains jack
(7) first, then connect it to a socket (230 V/ 50 Hz) .
Thus, the spotlight is ready for operation . Operate
it via a DMX light controller (
☞ chapter 8) or on its
own using the automatic control program adjusted
(
☞ chapter 7) . To switch off, disconnect the mains
plug from the socket .
For a more convenient operation, it is recom-
mended to connect the unit to a mains socket which
is switched on and off via a light switch .
Caution: Never connect the unit to the mains volt-
age via a dimmer!
The unit is protected against overheating; it will
automatically switch off when the temperature is
too high and switch on again after cooling down .