IMC Networks iMcV-LIM 10/100 Operation Manual Download Page 9

Page: 9 / 16

LED Operation

The iMcV-LIM 10/100 features several standard and diagnostic LEDs per port.

LNK

ACT

100

LFD

PNP
(AN)

PWR

100

ACT

LNK

Twisted Pair Port

Glows green when a twisted pair link is established.

Glows yellow when data is detected on the port.

Glows yellow when 100 Mbps data is detected on the
port.

Glows green when Link Fault Detection is enabled.

Glows green when Auto Negotiation mode is enabled
(transparency).

Glows green when unit has power.

Fiber Port

Glows yellow when 100 Mbps data is detected on the
port.

Glows green when data is detected on the port.

Glows green when a fiber link is established.

NOTE

Before either LNK LED will glow solid, the twisted pair and fiber optic cables must be
connected and the twisted pair crossover/ pass-through switch set correctly.

Summary of Contents for iMcV-LIM 10/100

















Search results

Summary of Contents for iMcV-LIM 10/100

Reviews:

Related manuals for iMcV-LIM 10/100

Brands by name

Popular brands

IMC Networks iMcV-LIM 10/100, Operation Manual

Search results

Summary of Contents for iMcV-LIM 10/100

Reviews:

Related manuals for iMcV-LIM 10/100

Brands by name

Popular brands